Layout; Starting Up; Electrical Connection - Scheppach Ixes Hda-14 Originalbetriebsanleitung

Warning! This power tool generates an electromag-
netic field during operation. This field can impair ac-
tive or passive medical implants under certain cir-
cumstances. In order to prevent the risk of serious
or deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operating
the power tool.

8. Layout

m ATTENTION!
Always make sure the device is fully assembled
before commissioning!
Installing the clip bolts (Fig. 2 - 3)
• Remove the transport lock screws (Fig. 2).
• Turn the nuts (4) over the entire length of the clip
bolts (3).
• Screw the clip bolts (3) into the threaded holes and
lock the nuts (4) against the top part of the housing
(Fig. 2).
• Drill holes into the ceiling and mount the four ceiling
mount clip bolts provided into the ceiling.
• Now hang the device onto the installation fastening
hooks using the chains provided. (Fig. 3)
NOTE: Fasten the device at least 2.13m above the floor.
Installing the heavy-duty air filter
To ensure the device is operated properly through air
circulation, make sure there is a gap of at least 50cm
on both sides of the air intake and at least 10cm from
the air outlet to the wall.
Keep other electrical devices, such as radios and tele-
visions, at least 1m from the device.
Do not plug the mains plug into the same socket as one
with radios, televisions or other electrical devices. This
can cause the screen to flicker or interference noises.
• Long-term use in the same place can make the walls
dirty.
• Ensure that the air intake and outlet are not covered
in order to ensure optimal air circulation and maxi-
mum performance.
9.

Starting up

m Attention!
Always make sure the device is fully assembled
before commissioning!
Switching on/off (Fig. 4 - 5)
• Press the "ON/OFF" button on the remote control
(5) or on the control panel (1) in order to switch the
device on or off.
Timer function (Fig. 4 - 5)
The "TIME" button on the remote control (5) or on the
control panel (1) controls the three different time set-
tings:
• Press the "TIME" button once so that the device
switches off automatically after one hour. (1H lamp
lights up on the control panel.)
• Press the "TIME" button twice so that the de-
vice switches off automatically after two hours.
(2H lamp lights up on the control panel.)
• Press the "TIME" button three-times so that the
device switches off automatically after four hours.
(4H lamp lights up on the control panel.)
Speed function (Fig. 4 - 5)
The "SPEED" button on the remote control (5) or on the
control panel (1) controls the three different air speeds.
• Press the "SPEED" button once so that the device
switches to the highest air speed. (HI lamp lights up
on the control panel.)
• Press the "SPEED" button twice so that the device
switches to the middle air speed. (MID button lights
up on the control panel.)
• Press the "SPEED" button three-times so that the
device switches to the slowest air speed. (LOW lamp
lights up on the control panel.)
Inserting and changing batteries in the remote con-
trol
• Remove the battery compartment cover located on
the bottom of the remote control by withdrawing the
bracket while lifting the cover.
• Insert the batteries (type AAA) (not included in the
scope of delivery). Ensure correct polarity.
• Insert the battery compartment cover again.

10. Electrical connection

The connection complies with the applicable national
regulations.
Connections and repair work on the electrical equip-
ment may only be carried out by electricians.
• Before commissioning, ensure that the mains voltage
matches with the operating voltage on the type plate.
• When using extension cables, please follow the
manufacturer's instructions.
www.scheppach.com GB | 21