Exsys EX-62020PoE-P Anleitung

CONNECTORS & STATUS LEDs
RJ45 Port:
Power over Ethernet IEEE802.3af/at (PoE+), Mode B
RJ45 Port
Pin Signal PoE Pin
1 BI_DA+
2 BI_DA-
87654321
3 BI_DB+
4 BI_DC+ VCC+
48V to 56V T-Block:
ATTENTION!
Please pay attention to the correct polarity!
Never connect the power supply to the terminal block
while it is switched on!
V- V+ V- V+
GND
Redundant power supply possible to reduce operational failure.
Both power supplies must use the same voltage!
Status LEDs:
PoE LED
PWR LED
LED Name Color LED Function
On: Linked
L/A Green
Flashing: Data Transmission
On: PoE is activated
PoE Yellow Flashing: Power Device (PD) detected
Off: No (PD) device connected
On: Powered
Power Green
Off: Power off
5
HARDWARE INSTALLATION
Please read the following installation instructions.
1. Install the EX-62020PoE-P on a mounting rail using the DIN-Rail kit.
2. Connect your network devices to the switch using a network cable.
3. Connect a PoE source to the uplink port of the switch. Alternatively, an optionally available
Signal PoE
power supply unit can be connected to the Terminal Block.
5 BI_DC- VCC+
4. After switching on, the PWR indicator lights up. If the indicator does not light up, check that
6 BI_DB-
the power source is connected correctly.
7 BI_DD+ VCC-
5. If all cables are connected correctly, the indicators light up according to the port status of
8 BI_DD- VCC-
the LEDs (page 5).
POWER MANAGEMENT
If the EX-62020PoE-P is supplied via a PoE power source (in accordance with IEEE 802.3bt,
PoE++) such as a PoE injector or a PoE switch, the device can pass on the incoming PoE
power to connected, PoE-compatible end devices (PoE pass-through function).
The maximum available output power depends on the total power of the PoE power source
used and is up to 30 W per port (PoE+).
Alternatively, the switch can be operated via the terminal block with a DC voltage of 48 to
56VDC. In this operating mode, the EX-62020PoE-P functions as a standalone PoE+ switch.
NOTICE & CLEANING
Procedure for STP Cable Grounding
When using shielded cables to connect two Ethernet devices, a ground loop may occur if the
Link / Activity LED
shielding on the cables generates an additional grounding connection path. This can cause
ground current to flow through to the Ethernet ports and damage the devices. If it is necessary
to use shielded cables, we recommend using a metallic RJ45 connector on one end and a non-
metallic connector on the other end. Alternatively, a patch panel can be used in between the
two devices to prevent ground loops from occurring.
Switch off the power supply before disconnecting modules or wires.
The propper power supply voltage is indicated on the product label. Check the voltage of your
power source to ensure you are using the correct voltage. DO NOT use a voltage higher than
what is specified on the product.
To clean the device, please use only a dry, non-fibrous cloth and remove the dirt with light
pressure. In the area of the connections, please make sure that no fibers of the cloth are left in
the socket.
Attention! Never use a moist or wet cloth for cleaning!
Germany:
EXSYS Vertriebs GmbH
Industriestrasse 8
61449 Steinbach
www.exsys.de
Switzerland: Italy:
EXSYS Vertriebs GmbH EXSYS Italia Srl
Dübendorfstrasse 17 Via Belvedere, 45/B
8602 Wangen I-22100 Como
www.exsys.ch www.exsys.it
6
EX-62020PoE-P
Anleitung Anleitung
Vers. 1.0 / 10.10.25
AUFBAU
Power LED
RJ45 Gbit 4x RJ45 Gbit
PoE-In PoE-Out
BESCHREIBUNG & TECHNISCHE DATEN
Der EX-62020PoE-P ist ein kompakter, industrietauglicher 5-Port Gigabit Ethernet Switch mit
Power over Ethernet (PoE++) Pass-Through-Unterstützung. Trotz seiner geringen Baugröße
bietet er an allen Ports volle Gigabit-Performance (10/100/1000 Mbps) und ist für den Einsatz in
anspruchsvollen Industrieumgebungen konzipiert. Die Stromversorgung kann wahlweise über
PoE++ (IEEE 802.3bt) oder über den integrierten Terminal Block (48-56 VDC) erfolgen. Eine
redundante Spannungszuführung ist möglich, um die Betriebssicherheit in kritischen
Anwendungen zu erhöhen. Die vier Downlink-Ports stellen jeweils bis zu 30 W Leistung für PoE
-fähige Endgeräte (Powered Devices, PD) wie IP-Kameras, IP-Telefone oder Access Points
bereit. Das robuste Metallgehäuse mit IP40-Schutzklasse
Betriebstemperaturbereich von -40°C bis +80°C gewährleisten zuverlässigen Dauerbetrieb auch
unter extremen Umgebungsbedingungen.
Kompatibilität: Gigabit Ethernet 10/100/1000Base-T
PoE: IEEE 802.3af/at/bt (PoE++), Mode/Alternative B
Betriebssysteme: Alle Betriebssysteme
Anschlüsse: 5x RJ45-Buchse, 1x Terminal Block 48-56 VDC
Lieferumfang: EX-62020PoE-P, DIN-Rail Kit, Wandmontagehalterung,
Anleitung
ACHTUNG!
Bei geerdetem Minuspol
unbedingt den Technischen Hinweis auf Seite 3
beachten.
1
48-56V T-Block für optional
erhältliches Netzteil
Status LEDs
sowie der erweiterte
der Stromversorgung