Residual Risks; Before Starting The Equipment; Operation - EINHELL TC-CD 12 Li Originalbetriebsanleitung

Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
L sound pressure level ..................... 65.3 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ....................... 76.3 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Drilling in metal
Vibration emission value a
K uncertainty = 1.5 m/s
Screwing without hammer action
Vibration emission value a
K uncertainty = 1.5 m/s
Warning!
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Anl_TC_CD_12_Li_SPK1.indb 20 Anl_TC_CD_12_Li_SPK1.indb 20
GB

Residual risks

Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

≤ 2.5 m/s
2
h Be sure to read the following information before
2
you use your cordless screwdriver for the fi rst
time:
1. Charge the battery pack with the charger
≤ 2.5 m/s
2
h supplied. An empty battery pack requires a
2
charging period of approximately one hour.
2. Only ever use sharp drill bits and screwdriver
bits which are suitable for the purpose and in
faultless condition.
3. Always check for concealed electric cables
and gas and water pipes when drilling and
screwing in walls.

6. Operation

6.1 Charging the LI battery pack (Fig. 2-3)
The battery is protected from exhaustive dischar-
ge. An integrated protective circuit automatically
switches off the equipment when the battery is
fl at. In this case the bit chuck will cease to turn.
Warning! Do not press the ON/OFF switch any
more if the protective circuit has actuated. This
may damage the battery.
1. Remove the battery pack (4) from the handle,
pressing the pushlock buttons (5) on the left
and right sides to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(8) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Insert the battery pack (4) into the battery
charger (8).
- 20 -
4.
If th
ase
•
•
If th
retu
•
•
to o
To e
long
it pr
whe
scre
6.2
The
cal
The
with
on s
•
•
•
The
indi
Imp
you
6.3
For
last
acti
mod
20.09.13 14:15 20.09.13 14:15