Inhaltsverzeichnis
Werbung
Operating Instructions
This chapter contains excerpts from the operating instructions. For further particulars please refer to the appropriate user instructions the part number of
which is indicated in the relevant spare parts list.
GENERAL OPERATION
Switching on and off
GB
• Press the ON/OFF button to switch the unit on.
– The Stand by indicator
6
goes out.
• To switch the unit to stand by press the ON/OFF
button again.
– Even if you switch your unit off, it remains connected
to the mains power supply.
The Stand by indicator
6
is always on when the unit
is connected to the mains power supply.
– If you want to completely disconnect the unit from the
power supply, remove the plug from the mains
socket.
Notes:
• When using mains supply, you can also use the
ON/OFF button on the remote control to switch the
unit on and off.
• When using battery supply, you can only switch the
unit on via the ON/OFF button on the set.
This is done to save battery life.
However, you can switch the unit to stand by via the
remote control.
• When using battery supply, the Stand by indicator
6
is always off and the display is not illuminated.
Source selection
• Select the desired source by pressing the respective
button (CD, TUNER or TAPE) on the unit or on the
remote control.
6
– The indicator of the selected source (CD
,
6
6
TUNER
or TAPE
) lights up.
CD PLAYER
CD handling
• Use only CDs which have the symbol
.
• To take the CD out of its box easily, press the centre
spindle while lifting the CD.
2
• Never write on a CD or attach any sticker to the CD.
• Always hold the CD at the edge and always store it
in its box after use with the label facing up.
• To remove dust and dirt, breathe on the CD and
wipe it with a soft, lint-free cloth in a straight line
from the center towards the edge. Cleaning agents
may damage the CD.
• Do not expose the CD to rain, moisture, sand, or to
excessive heat. (E.g. from heating equipment or in
motor cars parked in the sun).
Warning
CLASS 1 LASER PRODUCT means that the laser´s cons-
truction makes it inherently safe so that the legally
CLASS 1
prescribed maximum permissible ratiation values can
LASER PRODUCT
never be exceeded.
CAUTION: Using any equipment or devices other than
those described and specified in these operating
instructions, or tampering with the unit in any way, can
result in dangerous exposure to radiation.
Selecting 'CD'
• Press the ON/OFF button to switch the unit on.
• Press the CD button on the unit or on the remote control.
– The CD 6 indicator lights up.
– When you select CD when no disc is inserted or
when the disc is not inserted correctly, the display
TRACK
will first show 'TRACK 00 00:00' and afterwards
the indication no d1SC.
TRACK
Setting the clock
The clock can be set while the unit is in any mode of
operation. If you are in TUNER or CD mode and the
time is not being displayed, press DISPLAY on the
remote control until the time is shown.
• Press PROGRAM/TIME on the unit or on the remote
control.
– The hour starts flashing.
• Set the hour with UP/§ / ∞/DOWN.
• Press PROGRAM/TIME once more.
– The minutes start flashing.
• Set the minutes with UP/§ / ∞/DOWN.
• Press PROGRAM/TIME again to store the setting.
Inserting a CD
• Press OPEN to open the CD door.
• Insert the CD, printed side facing up. In addition to
standard 12 cm CD´s, you can also play 8 cm CD
singles without an adaptor.
1
• Close the cover.
– The CD player scans the contents list of the CD.
TRACK
After that, the total number of tracks and the total
playing time appear on the display.
Playing a CD
• Press PLAY/PAUSE 2; to start playback.
– The display shows the current track number and its
elapsed playing time.
• Adjust the sound with the VOLUME and UBS controls.
• For brief interruptions, press PLAY/PAUSE 2;.
– The playing time indication starts flashing.
TRACK
• To resume playback, press PLAY/PAUSE 2; again.
• To stop playback, press STOP 9.
– The total playing time and number of tracks will then
TRACK
appear on the display.
– The CD player also goes to position STOP:
– by pressing OPEN;
– when the end of the CD is reached;
– if the batteries run down or if the power supply is
interrupted.
• To take out the CD, open the CD door by pressing
OPEN.
• Open the CD door only if the CD player is in
position STOP.
TUNER
Selecting 'TUNER'
• Press the ON/OFF button to switch the unit on.
• Press the TUNER button on the unit or on the remote
control.
– The TUNER indicator
6
lights up.
Radio aerials
– For FM, pull out the telescopic aerial. To improve FM-
reception, incline and turn the aerial. Reduce its length
CH
MEMORY
if the FM-signal is too strong (very close to a transmitter).
FM
– For AM, the set is provided with a built-in aerial, so
the telescopic aerial is not needed. Direct the aerial
by turning the whole set.
Radio reception
CH
• Adjust the sound with the VOLUME and UBS controls.
FM
• Select the waveband using the BAND button on the
unit or on the remote control.
• Start the automatic station search by holding the
UP/§ or ∞/DOWN button (on the unit or on the
remote control) down for one or two seconds, and
then releasing it.
– The tuner automatically searches for the first station
with sufficient signal strength.
• Repeat this step to search for other stations.
• To tune to a weak station, briefly press the UP/§ or
∞/DOWN buttons several times until the correct fre-
CH
quency is displayed, or until reception is best.
AM
– When 'ST' appears on the display, you are
receiving an FM stereo transmitter.
• A disturbing noise, due to a weak FM stereo signal,
FM
can be suppressed by setting FM MONO/STEREO
to FM MONO.
– The 'ST' indication goes out and you will hear the
FM
FM station in mono.
CD PLAYER
SKIP UP § / ∞ DOWN
Selecting another track during play
• Press UP/§ or ∞/DOWN on the unit or on the
remote control.until the required track number
TRACK
appears in the display.
– The selected track begins to play.
• You can also select the desired track number directly
with the 1-0 / +10 buttons on the remote control.
Starting with a particular track
• Press UP/§ or ∞/DOWN until the required track
number appears in the display.
• Press PLAY/PAUSE 2;.
– Play starts from the selected track.
• You can also select the desired track number directly
with the 1-0 / +10 buttons on the remote control.
Searching for a passage during playback
• Hold down the UP/§ or ∞/DOWN button during
TRACK
playback to find a particular passage in forward or
backward direction.
– CD play continues at a low volume.
• Release the button when you have reached the
TRACK
desired passage.
Display modes
• During playback, press DISPLAY on the remote
control and the display shows you the CD´s
remaining playing time.
• Press this button again to display the actual clock
time.
• If you press this button once more, the display goes
back to showing the current track number and its
elapsed playing time.
Storing stations
You can store a maximum of 40 stations
(20 x FM and 20 x AM).
• Select the waveband using the BAND button.
• Select the desired station with the UP/§/∞/DOWN
buttons on the unit or on the remote control.
• Press the PROGRAM/TIME button on the unit or on
the remote control.
– 'MEMORY' starts flashing on the display.
• While 'MEMORY' is flashing , select the channel you
MHz
wish to assign to this station by repeatedly pressing
the REPEAT/SCAN button or directly with the 1-0 /
+10 buttons on the remote control.
• Press PROGRAM/TIME to store this station.
– 'MEMORY' disappears from the display. The display
now indicates the station's assigned channel, its
MHz
frequency and waveband.
• If you assign a station to a channel that had been
previously assigned to a different station, the old
station is deleted and replaced by the new one.
Calling up a stored station
• Select the waveband using the BAND button.
• Select the desired memory channel by repeatedly
pressing the REPEAT/SCAN button or directly with
the 1-0 / +10 buttons on the remote control.
– The display indicates the selected channel, the
station frequency and waveband.
kHz
Last station memory
means that the unit 'remembers'
LAST STATION MEMORY
MHz
the last station that was tuned to.
This function ensures that the station which was selected
before the tuner was switched off is automatically
selected again when your tuner is switched back on.
MHz
Intro
• In STOP mode, press the INTRO button on the
remote control.
– 'INTRO' lights up on the display.
INTRO
– Only the first 10 seconds of each title are played;
after the last title, the CD player stops.
• The function is deactivated by pressing STOP 9 (in
which case the CD stops) or INTRO; in this case the
remaining tracks are played back in the normal way.
• The intro function is not possible during playback of
a programme.
Repeat
Repeating the CD
• By pressing REPEAT/SCAN once, all tracks are
repeated.
– 'REPEAT' lights up; the CD will now be repeated
continuously.
REPEAT
Repeating a track
• By pressing REPEAT/SCAN twice, one track is
repeated.
– 'REPEAT' starts flashing; the track will now be
repeated continuously.
REPEAT
• To switch the repeat mode off, press REPEAT/SCAN
one more time, or press STOP 9.
• During playback of a programme, it is only possible
to repeat the whole programme, and not individual
programmed tracks.
Quicklinks ausblenden:
Werbung
Inhaltsverzeichnis
