Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
• Disconnect the appliance from the power supply.
• Remove food from the appliance and put it in a very
cool place or a thermally insulated bag.
• Leave the appliance door open.
• Remove the internal defrost water drain plug
(depending on model) (Fig. 8).
• Remove the external defrost water drain plug
(depending on model) and reposition it as shown in
figure 8.
• Use the separator (depending on model) inside the
product as a recipient for any remaining water, (D) as
shown in fig. 8. If there is no separator, use a shallow
container.
• Defrosting can be sped up by using a spatula to detach
the frost from the appliance walls.
• Remove the frost from the bottom of the appliance.
• In order to avoid permanent damage to the
appliance interior, do not use pointed or sharp
metal instruments to remove the ice.
• Do not use abrasive products or heat up the
interior artificially.
• Dry the inside of the appliance thoroughly.
• Refit the plug after defrosting..
CLEANING AND MAINTENANCE
• Remove the frost from the upper edges (see
Troubleshooting Guide).
• Clean the inside after defrosting, using a sponge
dampened with warm water and/or mild detergent.
• Clean the side vent (if provided).
Unplug the appliance before carrying out
maintenance operations. Do not use abrasive
products, scourers or stain-removers (e.g. acetone,
trichloroethylene) to clean the appliance.
To obtain the best results from your appliance, carry
out cleaning and maintenance at least once a year.
HANGING THE LID LIGHT BULB (if provided)
• Disconnect the appliance from the mains power supply.
• Remove the diffuser by following the sequence of steps
shown in the figure.
• Unscrew the light bulb and replace it with an identical
bulb of the same wattage and voltage.
• Refit the diffuser and plug in the appliance.
TROUBLESHOOTING GUIDE
1. The red LED (if provided) remains alight.
• Is there a power failure?
• Is defrosting in progress?
• Is the appliance lid properly closed?
• Is the appliance positioned near a heat source?
• Is the thermostat setting correct?
• Are the ventilation grille and condenser clean?
2. The appliance is too noisy.
• Is the appliance perfectly horizontal?
• Is the appliance in contact with other furniture or
objects that may cause vibrations?
• Has the packaging been removed from under the
appliance?
Note: gurgling noises from the refrigerating circuit after
the compressor cuts out are perfectly normal.
3. The green LED (if provided) is off and the
appliance is not working.
• Is there a power failure?
• Is the plug properly inserted in the socket?
• Is the electric cable intact?
4. The green LED (if provided) is off and the
appliance is working.
• The green LED is not working. Contact the After Sales
Service for a replacement.
5. The compressor runs continuously.
• Have hot foods been put in the appliance?
• Has the appliance lid been left open for a long time?
• Is the appliance positioned in a very warm room or
near heat sources?
• Is the thermostat setting correct?
• Has the fast freeze function (depending on model) been
pressed by mistake?
6. Too much ice on the upper edge.
• Are the defrost water drainage plugs correctly
positioned?
• Is the appliance lid properly closed?
• Is the appliance lid seal damaged or deformed? (See
chapter "Installation")
• Have the 4 protection pieces been removed? (See
chapter "Installation")
7. Condensation forms on the external walls of the
appliance
• It is normal for condensation to form under certain
atmospheric conditions (humidity above 85%) or if the
appliance is located in a damp or poorly ventilated
room.
The performance of the appliance is in no way affected.
8. The layer of ice on the internal walls of the
appliance is not uniform.
• This phenomenon is quite normal.
SAFEGUARDING THE ENVIRONMENT
1. Packing
The packing material is 100% recyclable and bears the
recycling symbol
. For disposal, comply with the local
regulations. Keep the packing materials (plastic bags,
polystyrene parts, etc.) out of the reach of children, as they
are a potential source of danger.
2. Scrapping/Disposal
The appliance is manufactured using recyclable material.
This appliance is marked in compliance with European
Directive 2002/96/EC on Waste Electrical and Electronic
Equipment (WEEE). By ensuring the correct disposal of this
appliance, you can help prevent potentially negative
consequences for the environment and the health of
persons.
The symbol
on the appliance, or on the accompanying
documents, indicates that this appliance should not be
treated as domestic waste but must be taken to a special
collection centre for the recycling of electrical and
electronic equipment.
When scrapping the appliance, make it unusable by cutting
off the power cable and removing the doors and shelves so
that children cannot easily climb inside and become
trapped.
Scrap the appliance in compliance with local regulations on
waste disposal, taking it to a special collection centre; do
Werbung
Inhaltsverzeichnis
