Listening through a Receiver (Home theater)
You can listen to sound through a receiver instead of the TV speaker.
1.
Press the TOOLS button. Press the ENTER
(HDMI-CEC)".
Press the ▲ or ▼ button to select "Receiver". Press the ◄ or ► button to
2.
select "On" or "Off".
3.
Press the EXIT button to exit.
➣
If your receiver supports audio only, it may not appear in the device list.
➣
The receiver will work when you have properly connected the Optical IN
jack of the receiver to the Optical Out jack of the TV.
➣
When the receiver (home theater) is set to On, you can hear sound output from the TV's Optical jack. When the TV is
displaying a DTV(air) signal, the TV will send out 5.1 channel sound to the Home theater receiver. When the source is
a digital component such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from the
Home Theater receiver.
➣
If there is a power interruption to the TV when the "Receiver" is set to "On" (by disconnecting the power cord or a
power failure), the "Select Speaker" may be set to "External Speaker" when you turn the TV on again. (see page 32)
Troubleshooting for Anynet +
Symptom
Anynet + does not work.
I want to start Anynet + .
I want to exit Anynet + .
The message Connecting to
Anynet + device... appears on the
screen.
The Anynet + device does not play. You cannot use the play function when Plug & Play is in progress.
The connected device is not
displayed.
The TV program cannot be
recorded.
The TV sound is not output
through the receiver.
button to select "Anynet+
Solution
Check if the device is an Anynet + device. The Anynet + system supports Anynet +
•
devices only.
•
Connect only one receiver (home theater).
Check if the Anynet + device power cord is properly connected.
•
Check the Anynet + device's Video/Audio/HDMI cable connections.
•
Check whether Anynet + (HDMI-CEC) is set to On in the Anynet + setup menu.
•
•
Check whether the TV remote control is in TV mode.
Check whether it is Anynet + exclusive remote control.
•
Anynet + doesn't work in certain situations. (Searching channels, Plug & Play,
•
etc.)
•
When connecting or removing the HDMI cable, please make sure to search
devices again or turn your TV off and on again.
Check if the Anynet + Function of Anynet + device is set on.
•
Check if the Anynet + device is properly connected to the TV and check if the
•
Anynet + (HDMI-CEC) is set to On in the Anynet + Setup menu.
•
Press the TV/DTV button on the TV remote control to switch to TV. Then press
the TOOLS button to show the Anynet + menu and select a menu you want.
Select View TV in the Anynet + menu.
•
•
Press the SOURCE button on the TV remote control and select a device other
than Anynet + devices.
•
Press P
/
and PRE-CH to change the TV mode.
(Note that the channel button operates only when a tuner-embedded Anynet +
device is not connected.)
You cannot use the remote control when you are coniguring Anynet + or
•
switching to a view mode.
Use the remote control when the Anynet + setting or switching to view mode is
•
complete.
Check whether or not the device supports Anynet + functions.
•
•
Check whether or not the HDMI cable is properly connected.
Check whether Anynet + (HDMI-CEC) is set to On in the Anynet + setup menu.
•
Search Anynet + devices again.
•
You can connect an Anynet + device using the HDMI cable only. Some HDMI
•
cables may not support Anynet + functions.
•
If it is terminated by an abnormal situation such as disconnecting the HDMI cable
or power cord or a power failure, please repeat the device scan.
Check whether the antenna jack on the recording device is properly connected.
Connect the optical cable between TV and the receiver.
English - 0
View TV
Device List
Recording
:
DVDR
DVDR Operation
Receiver
◄
On
Setup
U
Move
L
Adjust
►
R
Return