Jamara Land Rover Defender 110 SVX Li-Power 12.6 Gebrauchsanleitung Seite 10

GB
1. Attach the Front Wheels
• Slide the normal wheel (3) onto the front axle and slide a washer (20) onto the front axle.
• Tight a Locknut (19) to the end of the front axle with a spanner.
• "Snap" the wheel cover (4) to the wheel. Repeat this step for the other side.
2. Assembly the rear wheels
• First, cut the cable ties securing the gearbox.
• Remove the axle cover, nut, washer and cardboard tube from the rear axle.
• Install the gearbox, a wheel (2), a washer (20) and a nut (19) on the rear axle one after the
other.
• Repeat the process on the other side.
• Now tighten the nuts with two wrenches.
• Now attach the wheel covers (4) to the wheels.
3. Assembly the fender flares
• Align the fender extension with the designated position on the bodywork.
• Install it and secure it with screws.
Be sure to distinguish between the front wheel and the rear wheel (L1 = left front,
L2 = left rear; R1 = right front, R2 = right rear).
4. Steering wheel assembly
• Connect the cable from the steering wheel (5) to the cable of the model. Push the cable
back into the steering column. Make sure that the cables are not kinked, pinched or twisted.
• Align the steering wheel on the steering column and push the steering wheel onto the
steering column until it clicks into the holes.
5. Windshield assembly
• Align the windshield (6) with the corresponding openings on the car body, insert and push
them into place.
6. Installing the snorkel
• Make sure you hook the snorkel (12) onto the hook at the top of the windscreen first, then
hook it into the designated position on the bodywork at the bottom.
7. Mirror assembly
• Align the mirror (9) with the corresponding opening on the car body, insert and push it into
place. Remove the protective film from the mirror surface.
8. Install the winch
• Place the winch (13) at the front of the body and align it with the opening at the bottom of
the body.
A A B B
4 4
1 1 2 2 3 3 5 5
8 8 9 9 10 10
6 6
1
1
3 3
5 5 7 7
4
4
2
2
Functions transmitter
1. Forward
2. Backward
3. Speed
4. Power LED
5. Left
6. Brake
7. Right
8. Battery compartment
10 10
Functions
A Horn
D
D
Press the button to sound the horn.
B Music
Press the button to start the music.
C Foot pedal
To move the car, press the pedal down.
To brake or slow down, release pressure from the pedal.
D Soundboard
1 Music back / V-
Press
long press
C C 2 Music next / V+
Press
long press
3 USB
After inserting a USB stick, the soundboard starts playing
the tracks one after the other.
6 6 7 7
4 Voltage display
Clearly see the pattery power and help judge whether
the battery needs to be charged.
5 AUX
Connect MP3 device / mobile.
6 Song button
Play device's built-in music.
7 Mode
Press this button to enter the music mode.
8 Lightbutton
Turn the lights on / off / indicator
11 11 12 12
8 8
Fitting the transmitter batteries
Open the battery compartment cover on the
back of the transmitter and put 2 AAA batteries
making sure that it is corectly put in. Then close
the cover.
9. Battery connection
• Connect all connectors as shown and take care not to reverse polarity.
• Make sure that the red cable and the black cable are connected to the respective
connectors of the same colour.
10. Mounting the seat
• Slide the backrest (7) into the designated position from above.
• Place the seat (8) in position and secure it with 2 screws (18).
11. Mounting the roll bar
• First, connect the two side panels (11) to the cross bar (10) of the roll bar, then secure the
connection with two screws (18).
• Next, move the roll bar into the designated position, pressing it into the corresponding
openings until it clicks into place.
12. Charging Your Vehicle
• The power swich must be turned in OFF position when charging.
• Plug the charger port into the input socket and plug the charger plug into a wall outlet.
The battery will begin charging.
• The charge time is 7 hours.
• When the vehicle begins to run slowly, recharge thebattery.
• Do not charge the battery more than once within 24 hours.
• Charger and battery heat up during the charging process.
Warning!
The charger is not a toy. Only use the charger supplied.
•
• The battery may only be charged by or under the supervision of an adult.
The terminals must not be short-circuited.
•
• The charger must be checked regularly for damage to the cable, plug, housing and other
parts. If any damage is found, the charger must not be used until the damage has been
repaired.
• Let the model cool off sufficiently after each use before putting it back into operation.
When using an additional batteries let it cool off for minimum 15 minutes until the
model is operated again. Overheating can damage the electronics or may result in fire.
• Always disconnect the model from the charger immediately after charging. Always
disconnect the charger from the power supply immediately after disconnecting the
model. Inserting the rechargeable model or charger after charging will result in damage
tothe model, charger or the power supply (fire hazard).
• Use the charger only in dry rooms.
Only charge the vehicle with the enclosed charger (lithium). Only use the enclosed
rechargeable battery (lithium). Do not charge or operate any other vehicles with the
charger and battery.
= Previous track
= Volume down
= next track
= Volume up
Switch to transmitter mode.
To do this, locate the switch located under the
seat. It is secured with a protective cover and
a screw. Loosen the screw with a screwdri-
ver. Remove the protective cover. Select ‚RC'
for transmitter mode or ‚MANUAL' for manual
mode.
TIP: Keep the protective cover and screw for
future use.
9 Speed
High Speed - Change the speed of the car more quickly
Low Speed - Change the speed of the car more slowly
10 Power button
Long press it 3 seconds, turn the vehicle on and off.
Press the button briefly to turn the music on or off.
11 Forward
Press forward button, step on the foot switch the modell
will move forward.
12 Reverse
Press reverse button, step on the foot switch the modell
will move reverse.
Important!
The vehicle must be stationary before changing direction or
speed. Otherwise the gear unit and/or the motor could be
damaged.
Battery warning
Non-rechargeable batteries are not to be re-
charged! • Do not open! • Do nt dispose of in
fire! • Do not mix old and new batteries! • Do
not mix alkaline batteries, standard (carbon-
zinc) or rechargeable batteries! • Rechargeable
batteries are to be removed from the toy before
being charged! • Recharg3eable batteries are
only to be charged under adult supervision! •
The supply terminals are not to be short-cir-
cuited!
Binding transmitter and model
If the model does not respond to the transmit-
ter, press the forwards (1) and backwards (2)
buttons for about 3 sec until the Power LED (4)
flashes. Now switch on the model, the Power
LED is lit continuously.
If this does not work, repeat the process.