Securing Your Child - Apramo Modul One Bedienungsanleitung

04
Correctly install the child restraint system using the instruction
manual and make sure that no part is trapped in any possible
movement of the child restraint system, the vehicle seat or the
vehicle door during its daily use.
DO NOT modify or add anything to the product without the
approval of the competent authorities or the manufacturer as
this will void the warranty and may compromise safety and
performance.
Always ensure that the child restraint system is securely fastened
cause injury to the vehicle passengers in the event of a collision.
Please ensure that any straps holding the restraint to the vehicle is
tight and the straps restraining the child are adjusted to the child's
body. Any straps should not be twisted.
Any luggage or other objects liable to cause injuries in the event of
a collision must be properly secured.
NEVER leave your child alone or unattended in the child restraint
system.
Dry all metal parts after any contact with water to avoid rust
formation.
The illustrations in this manual are considered descriptive and may
Please ensure your product is purchased through an appropriate
sales channel. The manufacturer does not guarantee the quality of
second-hand products.
Before installing this child restraint system, always refer to the
vehicle manufacturer's instruction manual.
GB
important information
Always keep this manual together with the infant carrier for future
reference.
1.3 Parts of the apramo ® modül | one i-Size new born & baby car
seat Infant Carrier (Fig. 9)
1 Carrying Handle 7 Newborn Insert (40-60 cm)
2 8
Canopy Unlock Button for Stroller
3 Front Belt Guides 9 Harness Strap
4 10
Upper Belt Guide Harness Buckle
5 Carrying Handle Release 11 Quick Adjuster
Button 12 Adjustment Strap
6 Headrest Adjustment Lever
®
1.4 Parts of the apramo
17)
13 ISOFIX Connectors 20 Anti-Rebound System
14 ISOFIX Extension Button 21 ISOFIX Release Button
15 Rotation Plate (21A,21B)
16 Seat Release Strap 22 ISOFIX Connection Indicator
17 Rotation Lever 23 Locking Guides
18 Support Leg 24 Rotation Lock Indicator
19 Support Leg Adjustment
Button
installation with vehicle safety belt
2
installation with vehicle safety belt
2.1 Installation of the apramo ® modül | one i-Size new born & baby
car seat
® modül | one i-Size new born & baby car seat
The apramo can be
used from 40 to 75 cm / ≤ 11 kg for your baby. The modül | one Infant
Carrier can be installed with the vehicle's 3-point safety belts. To do
this, please follow the below steps:
1. Place the infant carrier on the vehicle seat, in the opposite
direction of travel.
2.
the belt passes inside the front belt guides (3) of the infant carrier
(Fig. 10).
3. Press the carrying handle release button (5) and rotate the
carrying handle (1), make sure the carrying handle is in contact
with the backrest of the vehicle seat and is properly locked. The
lower part of the belt must be under the carrying handle (Fig. 10).
4. Take the diagonal part of the safety belt to surround the infant
carrier, pass the belt through the upper belt guide (4) on the back
of the infant carrier (Fig. 10).
5. Tighten the safety belt by pulling its upper part towards the safety
belt retractor, to remove any slack from the installation.
® modül | one i-Size new born & baby car seat
6. The apramo is now
installed correctly.
WARNING!
® modül | one i-Size new born & baby car
NEVER PLACE THE apramo
seat IN FORWARD-FACING DIRECTION. IT CAN BE EXTREMELY
DANGEROUS FOR YOUR CHILD IN THE EVENT OF AN ACCIDENT.

2.2 Securing your child

1. Release the harness by pressing the button of the quick adjuster
(11) and pulling the harness strap (9) just above the buckle (Fig. 3).
Press the red button to open the harness buckle (10) (Fig. 6).
2. Place your child in the infant carrier. Pass the harness around
the child's shoulder, close the buckle by joining the two tongues
and joining them together into the buckle body (Refer to Fig. 6 in
reverse order). Remember not to place your child in thick clothes
as this will reduce the child's level of safety in the event of an
accident.
3. Adjust the headrest of the infant carrier by pulling the headrest
adjustment lever (6) that is located on the top (Fig. 1). The correct
position of the head restraint is horizontal to or a little bit below
the top of your child's shoulder (Fig. 2).
4. Adapt the harness by pulling on the adjustment strap (12) (Fig. 4).
As a reference, the correct harness tension is considered if there
is a maximum of 1 cm between your child's body and the harness.
5. Your child is now correctly secured.
2.3 Safe removal of your child
1. Loosen the harness belts by pressing the quick adjuster (11) and
gently pull on the pectoral straps, just above the buckle (Fig. 3).
2. Open the buckle, and then remove your child.
05
GB