Cleaning And Maintenance - Apramo Modul One Bedienungsanleitung

08 installation with apramo modül |
®
2. Loosen the harness by pressing the quick adjuster (11) and gently
pull on the pectoral straps, just above the buckle (Fig. 3).
3. Open the buckle, and then remove your child.
IMPORTANT:
DO NOT OPEN THE BUCKLE BEFORE LOOSENING THE HARNESS.
THIS COULD PREVENT THE CHILD FROM BREATHING NORMALLY.
3.5 Removal of the apramo ® modül | one i-Size new born & baby car
seat
1. Press the rotation lever (17) and turn the infant carrier to face the
vehicle door (Fig. 19).
2. Pull the seat release strap (16) and then lift the carrier. The infant
carrier now is released from the base (Fig. 20).
3.6 Removal of the apramo ®
To uninstall the base, follow the reverse steps to the installation of
the base (Fig. 16).
Retract the support leg by pressing the support leg adjustment
button (19) (Fig. 15).
Press the ISOFIX extension button (14) and pull the base towards
you.
To release the connectors from the anchor points, press the ISOFIX
release button 21A and the meantime pull the button 21B towards
you.
GB
ISOFIX rotating base / use of the newborn insert / use with stroller
Press the ISOFIX extension button (14), and retract the ISOFIX
connectors into the base so that they are protected for storage or
transportation of the base.
Turn the support leg to the leg storage position (Fig. 12). The base
can now be transported.
4
use of the newborn insert
The newborn insert must be used for better protection and comfort
for newborn babies. It must be removed when the child is over
60 cm.
5
use with stroller
Make sure the stroller is equipped with adapters compatible with
1.
® modül | one i-Size new born & baby car
the apramo seat.
Insert the adapter to the stroller, then place the infant carrier on
2.
the adapter. Make sure that it's correctly secured (Fig. 8).
To remove the infant carrier from the stroller, press the two unlock
3.
buttons for stroller (8) and lift the infant carrier (Fig. 8).
use of the canopy / cleaning and maintenance
6
use of the canopy
To open the canopy (2):
1. Press the two carrying handle release buttons (5) and rotate the
carrying handle (1) to upright position (Fig. 5).
2. Pull the canopy out from the gap between headrest and backseat,
then hang it on the grooves on the handle (1) (Fig. 5).
gap.
CAUTION!
WHEN THE SEAT IS RESTING ON A FLAT SURFACE OR ON A
TABLE, ALWAYS KEEP THE CARRYING HANDLE LOCKED AND
IN CONTACT WITH THE SURFACE AS SHOWN IN FIG. 7. THIS
PREVENTS THE SEAT FROM TIPPING OVER IF, FOR ANY REASON,
THE CHILD IS PLACED INSIDE.
7

cleaning and maintenance

7.1 Maintenance of the 3-point harness buckle of the infant carrier
A buckle failure can cause injuries. DO NOT lubricate or grease
any part of the 3-point harness buckle of the infant carrier.
The malfunction of the harness buckle is usually caused by an
accumulation of debris such as food crumbs or other small particles.
Some signs of a malfunction include:
The two tongues are released very slow when the red button is
pressed.
The two tongues do not engage in the buckle's body and are
ejected when you try to insert them in.
The tongues are inserted into the buckle's body, but without the
'click' sound signal.
The buckle needs a lot of force to open.
Normally, a rinse with warm running water is enough to solve the
problem. If not, contact the seller or the manufacturer immediately.
7.2 Cleaning the infant carrier covers
The infant carrier covers are removable and washable. Please
carefully refer to the washing label, sewn internally in the cover.
WARNING!
DO NOT USE THE INFANT CARRIER WITHOUT THE COVERS OR
WITH COVERS OTHER THAN THE ORIGINAL. A DIFFERENT COVER
COULD REDUCE THE SAFETY LEVEL, IN THE EVENT OF AN
ACCIDENT.
09
GB