Base Station - Hama Usedom Bedienungsanleitung

6. Installation
Note - Installation
• We recommend initially positioning the base station and measuring
station at the preferred setup locations without installing them and
carrying out all the settings - as described in 6. Operation - first.
• Do not install the station(s) until the settings are correct and the
radio connection is stable.
Note - Measuring station
• When installing the measuring station, make sure to choose a
shady location that is protected from precipitation. Direct sunlight
distorts the measurement results and moisture puts a strain on
the electronics.
Note
• The range of the radio transmission between the measuring station
and the base station is up to 50 m in unobstructed areas.
• Before installing, make sure that the radio transmission is not
influenced by interfering signals or obstacles such as buildings,
trees, vehicles, high-voltage power lines, etc.
• Before final installation, make sure that there is sufficient reception
between the desired installation locations. When installing the
measuring station, take care to ensure this is positioned so that it is
protected from direct sunlight and rain.
• The international standard height for measuring air temperature is
1.25 m (4 ft) above ground.
Warning
• Buy special or suitable installation material from a specialist dealer
for wall-mounting.
• Ensure that you do not install any faulty or damaged parts.
• Never apply force during assembly. These can damage the product.
• Before mounting, check that the wall you have chosen is suitable
for the weight to be mounted. Also make sure that there are no
electric, water, gas or other lines running through the wall at the
mounting site.
• Do not mount the product above locations where persons might
sit or stand.

6.1 Base station

• Place the base station on a flat surface using the stand (35).
• Alternatively, you can mount the base station on a wall using the
cut-out (33) on the back.
6.2 Measuring station
• You can also set up the measuring station on an even surface outdoors.
• We recommend mounting the measuring station securely and firmly
onto an outdoor wall.
• Secure the dowel, screw, nail, etc. in the wall provided.
• Hang the measuring station onto it using the cut-out (33) provided.
6
7. Operation
7.1 Connection to the measuring station
• After connection to the mains supply, the base station automatically
searches for a connection to the measuring station and carries out the
initial setup routine.
Note
• Initial setup takes around 3 seconds.
• The radio symbol measuring station (3) flashes when searching
for a connection.
• Avoid any operation of the buttons during this time! Otherwise,
errors and inaccuracies may occur in the values and their
transmission.
• The process is finished as soon as the indoor and outdoor
measurement data are displayed.
If no signal is received from the measuring station on a repeated basis,
press and hold the CH button (G) for at least 3 seconds to start the
manual search for the signal.
Note - temperature display
"HH.H" is shown in the display when the outdoor temperature is
above 50°C.
Note - faulty transmission of the measured values
• In some cases, interference caused by a WiFi network, computer, TV,
etc., for example, may cause the transmission of measured values
between the base and measuring station to fail.
• If this happens, resynchronise the stations by briefly removing the
batteries from both stations and reinserting them.
• If the measured values are not transmitted again, replace the
batteries with new ones.
• If necessary, choose a new location for the base station to avoid the
possible interference signals in the future.
• The measuring station and base station must not be placed more
than 50 metres apart from each other.
• Stay at least 2.5 m away from interference
7.2 Channel selection / Additional outdoor sensors
Note
• You can install two further outdoor sensors in addition to the
outdoor sensor supplied. When doing so, ensure the same channel
setting on the base station and each outdoor sensor.
• Suitable outdoor sensors can be found at www.hama.com
• Channel 1 is pre-selected.
• Press the CH button (G) repeatedly to set the same channel as on the
outdoor sensor in question. Channel 1, 2 or 3 is displayed.
• If the symbol appears, the weather station automatically changes
the channel display every 5 seconds. As soon as the required channel is
displayed, press the CH button (G) again to store it.