Lutron Pico PK2-2B Bedienungsanleitung

Pico Wireless Control
English
3 V- 10 mA
Mounting accessories sold separately.
For a complete listing of Pico wireless mounting accessories
and more information about Pico wireless controls, please visit
www.lutron.com/pico
PK2-2B PM2-2B PN2-2B PQ2-2B
PK2-2BRL PM2-2BRL PN2-2BRL PQ2-2BRL
PK2-3B PM2-3B PN2-3B PQ2-3B
PK2-3BRL PM2-3BRL PN2-3BRL PQ2-3BRL
P/N 040489 Rev. A
LUTRON LUTRON 11/2024
Important Notes
Please Read Before Installing
1. This install guide provides simple setup instructions for PowPak
systems only. If you are using your Pico wireless control with any other
Lutron system, please refer to the system setup guide. If you no longer
have your system setup guide, please download the latest version by
following the links at www.lutron.com
2. The Pico wireless control uses one (1) CR2032 battery (pre‑installed).
DO NOT use rechargeable batteries. Using improper batteries could
damage the Pico wireless control. DO NOT dispose of the battery
in normal household waste. Please recycle, take to a proper battery
disposal facility, or contact your local waste disposal provider regarding
local restrictions on the disposal or recycling of batteries.
Light
!
CAUTION: Risk of Fire, Explosion, Leakage, and Burns. Do Not Recharge, Disassemble,
Heat Above 212 °F (100 °C) or Incinerate. This product contains a lithium button/coin cell
battery. Keep batteries away from children. If a new or used lithium button/coin cell battery
is swallowed or enters the body, it can cause severe internal burns and can lead to death
in as little as 2 hours. Always completely secure the battery compartment. If the battery
compartment does not close securely, stop using the product, remove the batteries, and
keep the batteries away from children. If you think batteries might have been swallowed or
placed inside any part of the body, seek immediate medical attention. The battery in this
device contains Perchlorate Material — special handling may apply. For more information,
visit www.dtsc.ca.gov/hazardouswaste/perchlorate
3. The Pico wireless control must be paired with dimmer(s) / switch(es)
before it can communicate.
4. Up to 10 Pico wireless controls can be configured to work together with
a stand‑alone PowPak module.
5. The range of the Pico wireless control is 9 m (30 ft). Performance is
highly dependent on a variety of complex factors, such as:
• Distance between system components
• Geometry of the building structure
• Construction of walls separating system components
• Electrical equipment located near system components
6. Clean Pico wireless control with a soft damp cloth only. DO NOT use
any chemical cleaners.
7. DO NOT paint the Pico wireless control.
8. DO NOT mount the Pico wireless control to a metal surface.
CE Information
(For model numbers PK2‑, PQ2‑)
Hereby, Lutron Electronics Co., Inc. declares that the radio equipment models
listed above are in compliance with Directive 2014/53/EU. The full text of the
EU declaration of conformity is available at the following internet address:
www.lutron.com/cedoc
ImDA Compliance Information
(For model number PM2‑)
Complies with
ImDA standards
DA 103083
TRA
Light
REGISTERED NO:
ER61252/18
DEALER NO:
0016561/08
India Contact Address:
EEA Contact Address: UK Contact Address:
Lutron GL Sales and Service Pvt. Ltd
Lutron NL B.V. Lutron EA Limited
PO Box 15862 51 Lime Street Building 8A, 4th Floor, DFL Cybercity
Gurugram, Harayana 122002
1001 NJ, Amsterdam 3rd Floor, London EC3M 7DQ
Netherlands (Importer) England (Importer) India
Set-Up
(for PowPak systems only)
To communicate with other systems or devices, including RA2, GRAFIK
Eye QS, HomeWorks QS, QS sensor module (QSM), Quantum,
myRoom, Serena Shades, Vive, and Sivoia QS, refer to the system
setup guides.
Important: Set up a Pico wireless control to a load control
before use.
1. On the PowPak dimming module, hold the Toggle button " " for
6 seconds until lights flash (Figure 1).
The load status LED will begin flashing twice per second.
2. Press and hold the Off button on the Pico wireless control (Figure 2)
until the load status LED on the module and the load flash 3 times
(approximately 6 seconds).
3. Repeat step 2 to pair multiple Pico wireless controls with a single
PowPak dimming module. Repeat steps 1– 2 to pair a single Pico
wireless control with multiple PowPak dimming modules.
4. On the PowPak dimming module, hold the Toggle button " " for
6 seconds to save the association. Loads will flash and LED will quickly
blink for 2 seconds.
Figure 2
Figure 1
Power
Pico
PowPak Module
Wireless Control
Replacing the Battery in a Pico Wireless Control
1. Place a flathead screwdriver into the slot at the bottom of the Pico
Light wireless control. Twist to open. DO NOT press buttons without back Shade
enclosure on.
2. Slide the battery out, toward the top of the Pico wireless control.
3. Slide a new battery underneath the contact strap, with the (–) terminal
On Open
toward the front of the Pico wireless control.
4. Replace the back enclosure.
5. Confirm proper installation by turning the receiving device ON and OFF
using the Pico wireless control.
O Close
Shade
The Lutron logo, Lutron, HomeWorks, PowPak, Pico, Vive, Quantum, GRAFIK Eye, Serena, Sivoia, myRoom, RA2, and the design of the Pico remote are trademarks or registered trademarks
of Lutron Electronics Co., Inc. in the US and/or other countries. © 2017‑2025 Lutron Electronics Co., Inc.
Operation
Indicator LED
Flashes to indicate a button
press or when unit is in
programming mode.
Preset Button
(3B & 3BRL models only)
Tap once:
Devices go to preset
levels / positions. Activates
scene 16 when used in scene
mode with GRAFIK Eye QS
wireless applications.
Press and hold:
To save new preset level or
position, press and hold
for 6 seconds.
Shade Drape
Un-pairing a Pico Wireless Control
To un‑pair a previously paired Pico wireless control from your system perform the following
steps:
1. Quickly tap the OFF button, Figure 2, on the Pico wireless control
3 times and continue to hold it for 6 seconds after the third tap.
2. Once the indicator LED comes on solid, quickly tap the OFF button 3 times. Do not
continue to hold on the third tap.
3. To test that the Pico wireless control has been successfully removed from the system,
press the ON button a verify that the Pico wireless control no longer controls the load.
NOTE: This will remove all dimmers / switches with which it was previously paired.
Shade 1 Shade 2
Open Open
Close Close
Troubleshooting
Symptoms
Light, shade, or fan does not respond to
Pico wireless control.
Shade 1 Shade 2
When in set‑up mode, the LEDs on the
dimmer / switch flash when trying to set up
with the Pico wireless control or sensor.
Top Button
Lights brighten to full intensity, fan goes to highest speed,
and shades /draperies go to open limit. Activates scene 1
when used in scene mode with GRAFIK Eye QS wireless
applications.
Raise Button (2BRL & 3BRL models only)
Lights increase in intensity, fan speed increases, and
shades /draperies move towards open limit.
Lower Button (2BRL & 3BRL models only)
Lights decrease in intensity, fan speed decreases, and
shades /draperies move towards close limit.
Bottom Button
Lights dim to off, fan turns off, and shades /draperies go to
close limit. Activates "OFF" scene when used in scene mode
with GRAFIK Eye QS wireless applications.
Customer Assistance
www.lutron.com/support
For questions concerning the installation or operation of this product, call
Lutron Customer Assistance. Please provide exact model number when
calling.
Worldwide Headquarters
USA
TEL: +1.610.282.3800
FAX: +1.610.282.1243
Customer Assistance: 1.844.LUTRON1
Screen Drape
United Kingdom
TEL: +44.(0)20.7702.0657
FAX: +44.(0)20.7480.6899
Customer Assistance: +44.(0)20.7680.4481
Open Open FREEPHONE: 0800.282.107
Singapore
TEL: +65.6220.4666
FAX: +65.6220.4333
Customer Assistance: 800.120.4491
India
TEL: +971.600.521581
Customer Assistance: 000800.050.1992
Limited Warranty:
www.lutron.com/warranty or call 1.844.LUTRON1 (USA/Canada) or
1.610.282.3800 for a printed copy.
Close Close
Possible Causes
• The dimmer / switch failed to pair with Pico wireless control; see Set-Up.
• The dimmer / switch has already received and responded to a command or is already at the light
setting the Pico wireless control is sending.
• The Pico wireless control is outside the 9 m (30 ft) operating range.
• The battery in the Pico wireless control is low.
Screen Drape
• The battery in the Pico wireless control is installed incorrectly.
• The maximum number of Pico wireless controls or sensors has been paired with the
dimmer / switch. More Pico wireless controls or sensors cannot be added. See Un-pairing a
Pico Wireless Control.
Blackout
Open
Close
Blackout S
®