Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Start-Up
Assemble the appliance as described below depending on
the desired use.
Suction Pipe
• Insert the suction pipe with the two contact pins into
the connection on the hand appliance. It must audibly
engage.
• To disconnect the suction pipe, press the release (8) and
pull out the pipe at the same time.
Floor Nozzle with Turbo Brush
• The floor nozzle is suitable for all floor coverings except
for shag-pile carpets.
• During operation, the LEDs on the floor nozzle light up
for better visibility in dark areas.
CAUTION:
You cannot replace the LEDs.
• Stick the lower end of the suction pipe onto the connec-
tor on the floor nozzle. Note the contact pins on the floor
nozzle. The suction pipe must audibly s snap into place.
• To disconnect the suction pipe, press the release (10)
and pull out the pipe at the same time.
Nozzle Attachments
There are two different ways for connecting these nozzles
to the appliance:
Connection at the Handset
• Note the guide lug on the extra-long crevice nozzle and
on the combined crevice / brush nozzle. Hold the nozzles
so that the guide lug points upwards.
• Plug one of the nozzles into the port on the handset. The
connection must audibly engage.
• In order to release the respective nozzle, press the
release while simultaneously pulling it off.
Connection to the Suction Pipe
At the lower end of the suction pipe, you will find the same
plug connection as on the handset. Mount / dismount the
nozzle as described above.
Extra-long Crevice Nozzle
For vacuuming dirt from corners, joints and small gaps.
Combined Crevice / Brush Nozzle
This nozzle is suitable for removing dust from smaller
surfaces such as upholstery, furniture or curtains. Use
the nozzle with locked brush to prevent scratching of the
surface to be cleaned.
• For this, press the button (19) and push the brush to the
end of the nozzle. It must audibly engage.
• Press the button again to unlock the brush. Push the
brush up until you hear it click into place.
14
PC-BS3136A_IM 10.2024
Inserting / Removing the Battery Pack
The battery pack has been packed separately for transport
and must be inserted into the appliance.
• Push the battery pack into the opening on the handset.
The battery pack must engage audibly.
• If you want to remove the battery pack again, push and
hold the release (5) in direction . At the same time, pull
the battery pack out of the appliance.
Assembly the Wall Holder
The wall bracket is not only used for storage, but also as a
charging station. Therefore, attach the wall bracket near a
power socket.
1. Measure the height for the wall holder. Hold the vacuum
cleaner against the wall with the suction pipe and the
floor nozzle installed.
2. Hold the wall bracket against the wall. Mark 2 drill holes.
3. Drill the holes and insert the wall plugs into the wall.
4. To charge the appliance using the wall mount, you must
insert the power supply plug into the wall mount from the
rear. Press the power supply plug into the wall bracket
until it clicks into place. Then feed the mains cable
through the cut-out on the underside of the wall bracket.
5. Insert the screws through the holes of the wall holder.
6. Tighten the screws with a screwdriver hand-tight.
Charging the Battery Pack
- The battery pack must be charged before first use. Also
charge the battery pack to 100 % before using it for the
first time.
- The battery pack can only be charged in the appliance.
- It is normal for the appliance to heat up during charging.
1. Switch off the appliance.
2. Hang the appliance in the wall bracket. The appliance
must audibly click into place.
3. Connect the power supply unit to a tested socket. The
coloured ring around the control panel lights up red.
Charge the battery pack to 100 %.
- The charge level indicator shows the current charge
level of the battery pack in per cent.
- When the battery pack is fully charged, the coloured
ring goes out and 100 % is displayed.
4. Always disconnect the mains plug from the socket after
charging.
Using the Appliance
You can use the appliance as a floor vacuum cleaner or as
a handheld and upright vacuum cleaner (basic appliance).
1. Press and hold the release button at the top of the wall
bracket. At the same time, pull the appliance out of the
wall bracket.
2. Switch the appliance on.
24.10.24
Werbung
