Memorising A Remote Control - Nice Smx2 Anweisungen Und Hinweise Für Die Installateur

Memorising a remote control
A Whenthe memorisation p haseis activated, a nytrans-
mitter correctly recognised
the radio is memorised. Consider
and remove the aerial if necessary
of the receiver.
The procedures for memorising
formed within a certain time limit; please read and understand
whole procedure before starting.
In order to carry out the following procedure,
the button located on the box of the radio receiver (reference A), and
the corresponding LED (reference B) to the left of the button.
During the transmitter code memorisation
options may be chosen:
Mode I. Each transmitter button activates the corresponding
in the receiver, that is, button I activates output I , button 2 activates
output 2, and so on. In this case there is a single memorisation
phase for each transmitter; during this phase,
which button is pressed and just one tremory
Mode I memorising
Table "Bl"
(each button
Press and hold
2. Release the button
Within 10 seconds press the 1st button on the transmitter to be memorised,
3.
holding it down for at least 2 seconds
N.B If the procedure was memorised
If there are other transmitters to memorise, repeat step 3 within another 10 seconds
The memorisation phase finishes if no new codes are received for 10 seconds.
Table "82"
Mode II memorising
(each button
Press and release the receiver button as many times as the number of the
desired output (twice for output no. 2)
2. Make sure the Led flashes as many times as the number of the desired
output (2 flashes for output no. 2).
3. Within 10 seconds
holding it down for at least 2 seconds.
N.B.: If the procedure was memorised correctly, the Led on the receiver will flash 3 times.
If there are other transmitters to memorise, repeat step 3 within another 10 seconds
The memorisation phase finishes if no new codes are received for 10 seconds.
Remote memorising
It is possible to enter a new transmitter
out using the keypad. A previously
remote control must be available.
the characteristics of the previously memorised
first transmitter is memorised in mode l, the new one will also be
memorised in mode I and any of the buttons of the transmitter can
be pressed. If the first transmitter
one will also be memorised in mode II but the button activating the
Table "B3" Remote Memorising
Press the button
2. Press the button on the OLD transmitter
3. Press the button on the NEW transmitter
N.B If there are other transmitters to memorise, repeat the above steps for each new transmitter
Up to a maximum of 256 transmitters
deleted. For more advanced functions use the appropriate
within the reception range of
this aspect with care
to reduce the capacity
the remote controls must be per-
the
it is necessary to use
phase, one of these
output
it doesn't matter
sector is occupied.
activates the corresponding
down the receiver button for at least
the I ed lights up
correctly, the Led on the receiver will flash 3 times.
can be associated with a particular
press the desired button on the transmitter
in the receiver memory with-
memorised and operational
The new transmitter will "inherit"
one. Therefore, if the
is memorised in mode II the new
on the NEW transmitter for at least
3 times slowly
slowly and then release
can be memorised in the receiver. No one transmitter
programming
9
Mode 11. Each transmitter button can be associated with a particu-
lar output in the receiver, e.g., button 1 activates output 2, button 2
activates output 1, and so on. In this case, the transmitter
memorised, pressing the required button,
vate. Naturally, each button can activate just one output while the
same output can be activated by more than one button. One mem-
ory section is occupied for each button.
output in the receiver)
3 seconds
output)
to be memorised,
required output must be pressed on the first transmitter as must the
button required to be memorised
all the instructions in advance so you can perform the operations
sequence without interruptions.
(the NEVV one requiring code memorisation
already memorised), position yourself within the operating range of
the radio controls (within maximum range) and carry out the instruc-
tions listed in the table.
5 seconds and then release
can be cancelled;
unit.
must be
for each output to acti-
Example
3s
2s
x3
Example
2s
on the second. You need to read
Now, with the two remote controls
and the OLD one that is
Example
x5s
xl
all the codes must be
in
3