Werbung
Verfügbare Sprachen
Verfügbare Sprachen
-<robbe
INTRODU
High-performance
speed
controller
and easy programming.
Suitable
for 600
Ultra
motors
or multi-motor
models
with
SPECIAL
FET
POWER MOS field effect transistors (FETs)
Galvanic
separation
of receiver power circuit and motor
OPTO
power
circuit,
to eliminate
the
electric
motor
hec
High pulse frequency
for fine speed control without dama
ging the motor magnets
POR
Power On Reset
prevents the motor starting when the batte
ry is connected
Thermal
overload
protection
PCO
Low voltage
shut-off
RX filter - controller
shuts down
RXF
Easy programming
system
eps
TASTER
Programming
input
button
LED
Display of operating
and programming
High-quality high flex silicone cables
Splashproof construction
WP
Ultra-fine, super-smooth
control characteristics.
SPECIFICATION
Controller
type:
Forward
/ stop / reverse
Drive battery:
6... 18 NC / NiMH
Motor
current:
40 A
Pulse frequency:
I kHz
Dimensions:
67 x 39 mm
Weight:
231 g
Connector
system:
Battery:
direct
Motor:
direct
• The term „Motor current" means the average continuous
throttle forward",
which flows for the duration of one battery charge
(2000 mAh).
• The actual
current
varies according
operator's
driving
style. The controller
4
above
this value
without
problem.
TION
with forward
/ stop / reverse functions
700-size motors,
Pro, Sports and
400-
to 600-size
motors.
FEATURES
receiver
interference
caused
by
if transmitter
signa
fails
or
functions
/ 6 v
24 v
lead
acid
current at „fu
to the model
and the individua
can tolerate
brief current
peaks
USER
MANUAL
CONNECTING,
PROGRAMMING
USING
THE
CONTROLLER:
Solder the blue / white
power
leads to the motor terminals.
Before you carry out the following
procedure
2.
ensure that the motor (and any propeller
without
causing
damage
or injury.
3.
Locate
the receiver
lead attached
to the speed
nect
it to the
receiver
throttle
channel
4.
Switch on the radio control
system transmitter.
Switch on the receiving
system. Do not move
5.
6.
Connect
the drive battery.
7.
Hold the button
pressed
in for about
2 seconds.
button,
the
LED will flash once.
8.
Move the throttle
stick to the FULL THROTTLEFORWARD position;
the button
once
briefly to program
the FULL THROTTLE FORWARD positi-
on.
The
LED will
flash
twice
with
a one-second
9.
Move the throttle
stick to the NEUTRAL position;
briefly
to program
the NEUTRAL position.
one-second
intervals.
10.
Move the throttle
stick to the FULL THROTTLEREVERSE position;
button
once
briefly
to program
the FULL THROTTLE REVERSE position.
• This completes
the programming
procedure.
throttle stick forward through the FORWARD range, motor speed should
rise proportional
y. At the same time the LEDshould glow, its intensity
increasing as speed rises. At the STOP position of the stick the LED is off.
• When you move the throttle stick to the REVERSE range the LED will flash
at intervals
of 2 seconds.
INDING
• If it proves impossible
to program
the controller
repeat
steps 4 to 10 using slightly different
• If the motor spins in the wrong
direction,
wards when
you advance
the throttle,
the
motor
terminals.
NAVY
CONTROL
AND
Antriebsakku
Drive battery
Accu
it is absolutely
essential to
mounted on it) is free to spin
controller
and con
socket.
the throttle
stick.
When
you release
the
press
interval.
press the button
once
The LED will flash three times at
press the
If you now move the
as described
above,
stick positions.
i.e. the model
moves
back-
swap over the power
leads at
540
R NO.
8616
Motor
propulsion
motor
connection
Raccord
rnoteur
Fahrtregler
Motor
controller
Variateur
Akkuanschluß
Empfangerakku
Battery connection
Receiver battery
Raccord accu
Alim. du récepteur
Emptängeranschluß
Receiver
connection
Raccord du récepteur
Ernpfånger
Receiver
Vollgas
Full throttle
Plein gaz
Vorwårts
Forward
Marche
avant
Stop
Arrét
Neutral
Neutral
Neutre
Stopp
Rückwärtswarts
Backward
Marche
arriére
Vollgas
Full throttle
Plein gaz
Werbung
