Submenu 2.1: Setting Alarm Time; Submenu 2.2: Setting Duration Time Is Displayed; Submenu 2.3: Setting Duration Date Is Displayed - Nixie Clock Nocrotec Benutzerhandbuch

NOCROTEC – Nixie Clock – The Nixie Queen
• Press button 2 and button 3 to set the third digit (to
'1')
• Press button 1 (short) to jump to the fourth digit
• Press button 2 and button 3 to set the fourth digit (to
'2')
• Press button 1 (short) to jump to the fifth digit
• Press button 2 and button 3 to set the fifth digit (to
'0')
• Press button 1 (short) to jump to the sixth digit
• Press button 2 and button 3 to set the sixth digit (to
'9')
• Press button 1 long time (1 second) to leave the
submenu 1.2.
• Press button 1 long time (1 second) to leave the
main menu 1.
• Clock starts running in display mode.

Submenu 2.1: Setting Alarm Time

In this submenu alarm time can be set.
Display shows current alarm time at which alarm shall
ring.
If clock is set to AM/PM mode, nevertheless display
shows time in 24h mode.
Using button 2 and 3 the chosen digit can be set. To
switch to the next position, button 1 must be pressed.
To confirm this step shifting from digit to digit, the
following digit flashes. After the last digit, the first digit
shall be enabled again.
How to switch the alarm on and off will be explained in
chapter 11.
Setup Example:
• Alarm time shall be set to 07:30:00 o'clock.
• Clock is in display mode.
• Press button 1 (short) to enter the main menu 2.
• Clock stops and displays the current set alarm time.
• Press button 1 (short) to enter the submenu 2.1.
• Press button 2 (to count up) and button 3 (to count
down) to set the first digit (to '0')
• Press button 1 (short) to jump to the second digit
• Press button 2 and button 3 to set the second digit
(to '7')
• Press button 1 (short) to jump to the third digit
• Press button 2 and button 3 to set the third digit (to
'3')
• Press button 1 (short) to jump to the fourth digit
• Press button 2 and button 3 to set the fourth digit (to
'0')
• Press button 1 (short) to jump to the fifth digit
• Press button 2 and button 3 to set the fifth digit (to
'0')
• Press button 1 (short) to jump to the sixth digit
• Press button 2 and button 3 to set the sixth digit (to
'0')
• Press button 1 long time (1 second) to leave the
submenu 2.1.
• Press button 1 long time (1 second) to leave the
main menu 2.
• Clock starts running in display mode.
4
Submenu 2.2: Setting Duration Time is
Displayed
If this submenu is entered, the display shows
02:00:xx whereas 'xx' indicates the duration the
time is displayed. This value can be set from 00 to
59 seconds.
The value 00 means: Time shall not be displayed.
Accordingly, only date would appear in display
mode.
Using button 2 and 3 the chosen digit can be set.
To switch to the next position, button 1 must be
pressed.
To confirm this step shifting from digit to digit, the
following digit flashes. After the last digit, the first
digit shall be enabled again.
Setup Example:
• Value in this menu shall be set to 10 seconds.
• Clock is in display mode.
• Press button 1 (short) to enter the main menu 2.
• Clock stops and displays current set alarm time.
• Press button 2 once to reach submenu 2.2
• Press button 1 (short) to enter the submenu 2.2.
• Press button 2 (to count up) and button 3 (to
count down) to set the fifth digit (to '1')
• Press button 1 (short) to jump to the sixth digit
• Press button 2 and button 3 to set the sixth digit
(to '0')
• Press button 1 long time (1 second) to leave the
submenu 2.2.
• Press button 1 long time (1 second) to leave the
main menu 2.
• Clock starts running in display mode.
Submenu 2.3: Setting Duration Date is
Displayed
If this submenu is entered, display shows 03:00:xx
whereas 'xx' indicates duration date is displayed.
This value can be set form 00 to 59 seconds.
Value 00 means: Date shall not be displayed.
Accordingly, only time would appear in display
mode.
Using button 2 and 3 the chosen digit can be set.
To switch to the next position, button 1 must be
pressed. To confirm this step shifting from digit to
digit, the following digit flashes. After the last digit,
the first digit shall be enabled again.
Setup Example:
• Value in this menu shall be set to 05 seconds.
• Clock is in display mode.
• Press button 1 (short) to enter main menu 2.
• Clock stops and displays current set alarm time.
• Press button 2 twice to reach submenu 2.3
• Press button 1 (short) to enter submenu 2.3.
• Press button 2 (to count up) and button 3 (to
count down) to set fifth digit (to '0')
• Press button 1 (short) to jump to sixth digit
• Press button 2 and button 3 to set sixth digit (to
'5')
NOCROTEC
2009
©