Werbung
Verfügbare Sprachen
Verfügbare Sprachen
M. Colorful mood light
The colorful mood light will be only available
with the power supplied from a plug-in DC
adaptor
DESCRIPTION OF BUTTONS
The In-Outthermo mode-light clock has 6 major
function buttons on the front side and 1 major
function
buttons on the rear side
1 [MANUAL-MOOD-ALERT]SLIDESWITCH
This slide switch has three positions to slide:
MANUAL,
MOOD. and ALERT.
n MANUAL position, pressthe top of the
main unit to turn on mood light for 10 seconds.
While mood light is on, every press on the key
will extend the light for another 10 seconds
•
In MOODposition, the mood light will light up
permanently and change its color
continuously.
n ALERTposition,the alert light will light up
permanently and change its color according
to measured ambient temperature on indoor
or channel 1 remote sensor
Note: The mood & alert light will be only
available when connecting with the DC
adaptor.
2. [MODE]
Togglefor Clock, Calendaror Alarm display
mode
Note: The main unit will auto exitto clock
display mode if no key entry for 10 seconds
Press & hold 2 secondsto activate the setting
mode Of Clock-Calendar
or Alarm time
press once to increase the setting in Clock/
Calendar or Alarm time setting mode
press & hold 2 secondsto manually activate
or deactivate
the radio controlled function
permanently
10
Press once to decrease the setting in Clock/
Calendar OrAlarm time setting mode
Toggle Daily Alarm on/off while in Alarm
display mode
5 [CHI
Press shortlyto toggle display of Indoor
temperature, remote thermo from Channel1,
Channel 2 and Channel 3 to Auto-scroll
which alternately display indoor temperature
and the three remote temperatures
Note: when in the Auto scroll mode,
scrolling time for Indoor and each channel is
4 seconds. Only registered channel(s) will be
shown up in the Auto scroll mode,
unregistered channel(s)will be skipped
Press & hold 2 seconds to activate or
deactivate searching modefor remote sensor
6 [MEMI
Toggleto view the Max/Min reading of the
ndoor & Outdoortemperature.
Press & hold 2 seconds to clear the Max/Min
temperature memories of Indoor & al
Remote
7 (ALERT)
Press & hold 2 secondsto enter Mood Light
setting mode, use [A I or [
button to set
Mood Light alert according to ndoor
temperature or Channel1temperature
press [ALERT]to confirm
8 [SNOOZE-LIGHT]
press the top of the main unit to activate
[SNOOZE-LIGHT] b utton to turn on backlight
for 10seconds. Meanwhile, the mood light
WII be light up for 10seconds if the main
unit is connecting with the DCadaptor and
the (MANUAL-MOOD-ALERT]slide switch is
in the MANUAL position
Stop alarm sound temporary for 5 minutes
when alarm sounds
Note: When the clock is beeping, pressing
any button will stop it except the
[SNOOZE-LIGHT] button
BATTERY INSTALLATION FOR MAIN UNIT
Removethe battery door.
2 Insert 3 pieces AAA size 15V alkaline battery
mode
as indicate bythe polarity;
Close the battery door.
Note: Replace the batteries when the low
battery indicator appears on the top-middle of
the Ower LCD
BATTERY INSTALLATION FOR REMOTE SENSOR
1. Removethe battery door
2. Insert 2 pieces AAA size 15V alkaline battery
as indicate bythe polarity;
3. Close the battery door
Note: Replace the batteries when the low
battery indicator in each channel appears on
the top- eft of the upper LCD.
GETTING STARTED
This In Outthermo mood-light clock was
designed for easy set up. Forbest operation, the
fol owing steps are required to be done in the
proper sequence.
Insert batteries to the main unit, it wi
automatically search the remote sensors
(while they are in effective transmission
range) for 2 minutes and then receive RCC
signal for 10minutes
Note: Main unit can't be programmed
manually during RFsearching and RCC
reception
Insert batteries to the remote sensor and set
it to desired channel by pressing [CHI button
The main unit will show the temperature
reading of the remote sensor in corresponding
channel if it receives the RFsignal and
registers the remote sensor successfully.
4. Position the remote unit and main unit within
effective transmission range, which is, in
usual circumstances, is 30 meters (100feet)
The remote sensor should be placed away
from direct sunlight, rain or snow
WIRELESS REMOTE SENSOR REGISTRATION
PROCEDURE
Wthin 2 minutes of power up the main unit,
activates
the sensor as follows:
Insert the 2 AAA batteries into the sensor unit
whilethe ' i)) ' iconinthe mainunitis
flashing to prompt the userthatthe main unit
is in sensor searching mode.
The LEDon the front panel of the sensor will
start flashing at a rate of one time per around
2 seconds to indicate
channel 1 is in use
While the LEDis flashing, press once the [CHI
key wil change the sensor channel setting to
2. Keeptoggle on [CHI key can change
channel setting up to 3. The LEDis blinking at
afrequency to indicate the channel setting
i.e.continuous blinking 2times indicates
channel 2is selected If no key entry for 10
seconds, it will exit the channel setting mode
andtransmit the RFsignal of the temperature
reading
The main unitwill show the temperature
reading of the remote sensor in
corresponding channel if it receives the RF
signal and registers the remote sensor
successfully.
The
' icon in main unit wil stop flashing
4
after two minutes to prompt user that it
already exits sensor searching mode. In this
case, the user must press and hold [CHI
button for 2 seconds to re-enter sensor
searching mode and repeat above steps if he
wants to register a new remote sensor.
Werbung
