Werbung
Verfügbare Sprachen
Verfügbare Sprachen
USING THE CONTROL PANEL
NOTE: Press the dial to START or STOP any program. Turn to select.
POWER
Press to power
BLENDSENSE
the unit on and off.
Intelligent one-touch program
that senses your ingredients
MANUAL
and blends to perfection.
Adjustable speed for
MODE (Jug only)
total blending control.
Preset processing programs (LARGE
CHOP, SMALL CHOP, and MINCE)
that chop and mince.
PROCESSING MODE PROGRAMS
LARGE CHOP, SMALL CHOP, AND MINCE: Jug only.
Smart preset programs combine unique pausing patterns that chop for you. Press
MODE, turn the dial to select your desired program, then press START/STOP. The
program will automatically stop when complete. Press the dial again to stop the
program sooner. They do not work in conjunction with the BlendSense program or
Manual programs.
NOTE: Number of seconds is displayed for the program's runtime.
MANUAL PROGRAMS
Go manual for total control of your blending speed and textures. Press MANUAL,
turn the dial to select your desired program, then press START/STOP. When
selected, each speed runs continuously for 60 seconds. Press the dial again to
stop the program sooner. Manual programs do not work in conjunction with the
BlendSense program or Processing Mode programs.
VARIABLE SPEED CONTROL (Speeds 1–10): Jug only.
START SLOW (Speeds 1–3): Always start at low speed to better incorporate
ingredients and prevent them from sticking to the sides of the vessel.
DIAL UP THE SPEED (Speeds 4–7): Smoother blends call for higher speeds.
Low speeds are great for chopping veggies, but you'll need to ramp up for
purées and dressings.
HIGH-SPEED BLENDING (Speeds 8–10): Blend until your desired consistency
is reached. The longer you blend, the better the breakdown and smoother the
outcome will be.
LOW, MEDIUM, HIGH Speeds: Single-Serve Cup only.
NOTE: Once speed is selected, runtime will count up on the display in seconds.
ninjakitchen.eu
USING THE JUG
IMPORTANT:
• Review all warnings at the beginning of this Owner's Guide before proceeding.
• As a safety feature, if the jug and lid are not properly installed, the timer will display INSTALL
and the motor will be disabled. If this happens, repeat step 5 on this page.
WARNING:
loose and sharp and NOT locked in place. If using the pour spout, ensure the lid is fully locked onto the
blender jug. If pouring with the lid removed, carefully remove the Stacked Blade Assembly first,
PULSE
holding it by the shaft. Failure to do so will result in a risk of laceration.
Operates only when PULSE
is pressed. Use short presses
for short pulses and long
NOTE:
presses for long pulses.
• DO NOT add ingredients before completing installation of the Stacked Blade Assembly.
• If the Stacked Blade Assembly is not fully seated, you will not be able to install and lock the lid.
• The jug lid handle will not fold down unless it is attached to the jug.
• DO NOT process or grind dry ingredients.
• For best results, blend fresh leafy greens and herbs in the single-serve cup.
1
Plug in motor base and place on a clean, dry, level surface such as a
countertop or table.
2
Lower the jug onto the motor base. The handle should be aligned slightly to
the right and the jug should be oriented so the LOCK symbols are visible on
the motor base. Rotate the jug clockwise until it clicks into place.
3
Exercising care, grasp the Stacked Blade Assembly by the top of the shaft and
place it onto the drive gear inside the jug. Note that the blade assembly will fit
loosely onto the drive gear.
6a If using the BlendSense program, simply press the dial. The program will
automatically stop once complete. To stop the unit at any time, press the dial again.
6b If using a Processing Mode program, select MODE, then use the dial to select
your desired program. To start, press the dial. The program will automatically
stop once complete. To stop the unit at any time, press the dial again.
6c If using a Manual program, select MANUAL, then use the dial to select your
desired speed (1–10). To start, press the dial. Once the ingredients have
reached your desired consistency, press the dial again or wait 60 seconds
for the unit to come to a complete stop on its own.
7
To remove the jug from the motor base, turn the jug anti-clockwise and then lift up.
8b For thicker mixtures that cannot be emptied through the pour spout,
remove the lid and Stacked Blade Assembly before pouring. To remove
the lid, press the RELEASE button and lift the handle. To remove the
blade assembly, carefully grasp it by the top of the shaft and pull straight
up. The jug can then be emptied.
9 Turn the unit off by pressing the Power button. Unplug the unit when
finished. Refer to the Care & Maintenance section for cleaning and
storage instructions.
Ninja Detect Total Crushing® & Chopping Blades (Stacked Blade Assembly) are
4 Add ingredients to the jug. DO NOT add ingredients past the MAX
LIQUID line.
5
Place the lid on the jug. Press down on the handle until it clicks into
place. Once the lid is locked in place, press the Power button to turn
unit on. The BlendSense program will illuminate.
8a To pour out thinner mixtures, ensure the lid is
locked in place, then open the pour spout cap.
ninjakitchen.eu
Werbung
