EuroLite LED PIXEL POLE Bedienungsanleitung Seite 15

Power Cord
• Always plug in the power plug least. The power plug
must always be inserted without force. Make sure that
the plug is tightly connected with the outlet.
• Never let the power cord come into contact with other
cables! Handle the power cord and all connections
with the mains with particular caution! Never touch
them with wet hands, as this could lead to mortal
electrical shock.
• Never modify, bend, strain mechanically, put pressure
on, pull or heat up the power cord. Never operate next
to sources of heat or cold. Disregard can lead to
power cord damages, fire or mortal electrical shock.
• The cable insert or the female part in the device must
never be strained. There must always be sufficient
cable to the device. Otherwise, the cable may be
damaged which may lead to mortal damage.
• Make sure that the power cord is never crimped or
damaged by sharp edges. Check the device and the
power cord from time to time.
• If extension cords are used, make sure that the core
diameter is sufficient for the required power
consumption of the device. All warnings concerning
the power cords are also valid for possible extension
cords.
• Always disconnect from the mains, when the device is
not in use or before cleaning it. Only handle the power
cord by the plug. Never pull out the plug by tugging
the power cord. Otherwise, the cable or plug can be
damaged leading to mortal electrical shock. If the
power plug or the power switch is not accessible, the
device must be disconnected via the mains.
• If the power plug or the device is dusty, the device
must be taken out of operation, disconnected and
then be cleaned with a dry cloth. Dust can reduce the
insulation which may lead to mortal electrical shock.
More severe dirt in and at the device should only be
removed by a specialist.
Liquids
• There must never enter any liquid into power outlets,
extension cords or any holes in the housing of the
device. If you suppose that also a minimal amount of
liquid may have entered the device, it must
immediately be disconnected. This is also valid, if the
device was exposed to high humidity. Also if the
device is still running, the device must be checked by
a specialist if the liquid has reduced any insulation.
Reduced insulation can cause mortal electrical shock.
Foreign Objects
• There must never be any objects entering into the
device. This is especially valid for metal parts. If any
metal parts like staples or coarse metal chips enter
into the device, the device must be taken out of
operation and disconnected immediately. Malfunction
or short-circuits caused by metal parts may cause
mortal injuries.
Maintenance and Service
• There are no serviceable parts inside the device.
Maintenance and service operations are only to be
carried out by authorized dealers!
• Disconnect from mains before cleaning! Never use
solvents or aggressive detergents in order to clean
the device! Rather use a soft and damp cloth.
www.eurolite.de
Installation
• For installation in public or industrial areas, a series of
safety instructions have to be followed that this
manual can only give in part. The operator must
therefore inform himself on the current safety
instructions and consider them. The manufacturer
cannot be made liable for damages caused by
incorrect installations or insufficient safety
precautions!
• The device has to be installed out of the reach of
people and should be installed outside areas where
persons may walk by or be seated.
• The installation of the device has to be built and
constructed in a way that it can hold 10 times the
weight for 1 hour without any harming deformation.
• When rigging, derigging or servicing the device
staying in the area below the installation place, on
bridges, under high working places and other
endangered areas is forbidden.
• If the device shall be lowered from the ceiling or high
joists, professional trussing systems have to be used.
The device must never be fixed swinging freely in the
room.
• Hanging devices may cause severe injuries when
crashing down! If you have doubts concerning the
safety of a possible installation, do NOT install the
device!
• Overhead rigging requires extensive experience,
including (but not limited to) calculating working load
limits, installation material being used, and periodic
safety inspection of all installation material and the
device. If you lack these qualifications, do not attempt
the installation yourself, but instead use a
professional structural rigger. Improper installation
can result in bodily injury and or damage to property.
• The installation must always be secured with an
appropriate secondary safety element (e.g. steel
rope). This secondary safety attachment must be
constructed in a way that no part of the installation
can fall down if the main attachment fails. You must
only use safety bonds complying with DIN 56927,
quick links complying with DIN 56927, shackles
complying with DIN EN 1677-1 and BGV C1 carbines.
The safety bonds, quick links, shackles and the
carbines must be sufficiently dimensioned and used
correctly in accordance with the latest industrial safety
regulations (e. g. BGV C1, BGI 810-3). The maximum
drop distance must never exceed 20 cm. A safety
bond which already held the strain of a crash or which
is defective must not be used again.
• The operator has to make sure that safety-relating
and machine-technical installations are approved
• by an expert before taking into operation for the first
time and after changes before taking into operation
another time.
15