Conrad 1008495 Bedienungsanleitung Seite 3

G
O P E R A T I N G I N S T R U C T I O N S
WLAN-/LAN-Colour Camera
Item no. 1008495
Intended use
The product is intended for surveillance by means of the integrated camera. It can either be op-
erated directly via a 10/100MBit network (RJ45 connection) or wireless via WLAN (802.11b/g,
54MBit).
The camera is suitable for the operation in indoor and outdoor areas. However the plugs at the
cable end (RJ45, low-voltage connector) and the button must not get damp or wet.
The power is supplied via the enclosed power adapter. It must not get damp or wet either and
has to be connected and operated in a dry indoor room.
Please bear in mind that it is prohibited by law to observe strangers with a camera without
their knowledge and consent. Observe the rules and regulations of the country where you are
using the camera.
The safety instructions and technical data must be followed without fail!
Any use other than that described above could lead to damage to this product and involves
the risk of short circuits, fire, electric shock, etc. No part of the product may be modified or
converted!
This product complies with the applicable national and European requirements. All names of
companies and products are the trademarks of the respective owners. All rights reserved.
Contents
• Camera
• WLAN antenna
• Network cable
• Mounting bracket with mounting material
• AC adapter
• CD
• Manufacturer's operating instructions in English (either as printed hardcopy or as PDF on the
CD)
• Quick guide
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any resulting
damage!
We shall not accept liability for damage to property or personal injury caused
by incorrect handling or non-compliance with the safety instructions. In such
cases, the warranty will be null and void.
a) General
• The unauthorised conversion and/or modification of the product is not permitted
for safety and approval reasons (CE). Never dismantle the product.
• Any maintenance or repair work may be only performed by an authorised repair
shop.
• Do not leave packaging material carelessly lying around, since it could become a
dangerous plaything for children.
• In commercial institutions, the accident prevention regulations of the Employer's
Liability Insurance Association for Electrical Systems and Operating Facilities are
to be observed.
• If you have any questions that are not answered in this manual, please contact our
technical service or other specialist.
b) Wall plug transformer
• The design of the power adapter complies with Protection Class II. Use only a
standard mains socket as the power source for the wall plug transformer.
The mains socket into which the wall plug transformer is plugged must be easily
accessible.
• Only use the wall plug transformer provided to power the docking station.
• Do not pull the wall plug transformer from the mains socket by pulling on the cable.
Hold it on the sides of the casing and pull it out of the mains socket.
• If the AC adapter is damaged, do not touch it; there is a danger to life from electric
shock!
www.conrad.com
Version 02/14
Getting started, Connection via RJ45
• Connect the WLAN antenna via the corresponding connection socket at the back of the camera.
• Connect the RJ45 connector (at the end of the camera's cable) to a 1:1 connected network
cable with its network, e.g. a network switch.
• Connect the corresponding plug of the wall plug transformer provided to the round low-volt-
age connector of the camera's connection cable and connect the wall plug transformer with
a mains socket.
There are two further LEDs on the RJ45 input: The top, right-hand LED indicates the link
status (network cable connection ok). The top, left-hand LED indicates data transfers via LAN
cable.
• Insert the provided CD into the appropriate drive on your computer and start the installation
programme (programme name: "IPCamSetup.exe").
Follow the instructions of the software. Windows needs to be restarted afterwards.
First, switch off the mains voltage to the socket to which the wall plug transformer
is connected (switch off at the corresponding circuit breaker or remove the safety
fuse or switch off at the corresponding RCD protective switch, so that the socket
is fully disconnected).
You can then unplug the wall plug transformer from the mains socket. Dispose of
the faulty wall plug transformer in an environmentally friendly way, do not use it
any more. Replace it with a wall plug transformer of the same design.
c) Operation
• The product is not a toy. Devices operated using mains voltage do not belong in
the hands of children. Therefore, be especially careful when children are around.
Use the product where it is out of the reach of children.
• The use of this camera does not replace the personal supervision of children or
people who require special assistance, but only serves as a support for this super-
vision.
• The camera is suitable for the operation in indoor and outdoor areas. However, the
plugs at the cable end (RJ45, low-voltage connector) and the button must not get
damp or wet.
However, never mount the camera in or under water; this will destroy the device.
The wall plug transformer may not get wet or moist. It must be connected and op-
erated in a dry indoor room, otherwise there is a danger to life through an electric
shock!
• Never use the product immediately after it has been taken from a cold room to a
warm one. The condensation that forms might damage the product under certain
circumstances. The wall plug transformer also poses a risk for a potentially fatal
electric shock!
Allow the product to reach room temperature before connecting it to the power
supply and putting it to use. This may take several hours.
• Avoid the following adverse conditions at the installation location and during trans-
port:
- Dust or flammable gases, fumes or solvents
- Strong vibrations, impacts, or blows
- Strong magnetic fields such as those found in the vicinity of machinery or loud-
speakers
• When setting up the product, make sure that the cable is neither kinked nor
pinched.
• Handle the product with care; it can be damaged by impacts, blows, or accidental
falls, even from a low height.
• If the camera is used with other devices (e.g. a monitor), the operating instructions
and safety notices for these devices must be followed.
• Disconnect the power supply from the power socket if the camera will not be used
for a while (e.g. storage).
• Safe operation can no longer be assumed if:
- the device is visibly damaged,
- the device no longer works
- the device has been stored under adverse conditions for a long time
- it was exposed to heavy loads during transport
Test the camera before installing it permanently in the desired place using the
mounting bracket provided.
To make all the settings, the camera should always be connected first to the compu-
ter via RJ45. Only once the camera is working properly can WLAN operation be set
up.
For the set-up process to be straightforward, it is essential for your network to have
an active DHCP-Server (e.g. as contained in every router).