eta 0706 Bedienungsanleitung Seite 13

II. DESCRIPTION OF FEATURES (FIG. 1)
A – Brush body
A1 – ON/OFF switch
A2 – battery/active mode indicator light
A3 – protective cover
A4 – Power USB slot
B – Brush (2 pcs included)
B1 – brush head
C – Micro-USB cable: (Use AC power adapter with USB or mobile power)
Note: Replacement brushes B can be purchased under order number
ETA 070690100.
III. INSTRUCTIONS FOR USE
Remove all packaging materials and take out the appliance and any
accessories. Parts which come in contact with the oral cavity must be
rinsed in warm drinking water before first use.
CHARGING THE BRUSH (Fig. 2).
1) Make sure the appliance is off. While charging, the appliance cannot
be in use. If the appliance is turned on and you start charging, the
appliance shall switch off.
2) Put the provided charge USB cable C into the charge slot A4 of brush
body, connect the other charger compatible AC wall adapter or mobile
power.
3) The charging procedure is signalled by a flashing A2 red LED indicator.
4) tWhen the battery is fully charged, the A2 LED indicator it will go off.
Unplug the adaptor from the wall socket first and only then unplug the
connector from the case.
5) For a full charge, the battery needs to be charged for approximately 4
hours. Depending on the cleaning mode used, a fully charged battery
will provide approximately 80 minuts of operation.
Note: Although the brush should not be charged before it is fully
discharged, we recommend charging it at regular intervals (e.g.
after 2-3 weeks of use) in order to ensure optimum battery life.
– During operation, the A2 LED indicator is lit, when the battery of the
accumulator is low and it needs to be recharged, the LED indicator
starts flashing (10x).
– Do not exceed the recommended time of charging during regular
charging!
– The appliance warms up during charging, but this is normal and not
a defect.
– The operating time is only approximate. The time depends on the
condition of the battery, ambient temperature, age, method of charging.
USE
Before use, slide the brush B onto the brush body A to connect them
(See Fig. 1). A small gap will remain between the brush body A and the
coloured ring B2 which is not a defect. To remove the brush, proceed
the other way round. Do not switch on the appliance without the brush
attached! Moisten the brush and apply a small amount of toothpaste
on it. Put the brush to the teeth at a slight angle towards the gums (see
Fig. 3) and switch on any mode firstly by pressing the on/switch button
A1. Move the brush slowly along the teeth back and forth, applying a
slight pressure, so as not to miss any tooth or area in the mouth. Clean
each tooth for about 2-3 seconds. The brush operating time is limited
to 2 minutes which corresponds to the time for cleaning recommended
by experts. If you wish to continue cleaning, simply switch on the brush
again.Each part of the mouth (quadrant) should be cleaned for about
30 seconds (see Fig. 4). A short interruption of the brush operation will
prompt you to move to another quadrant after this time elapses.
– If this is your first sonic toothbrush and you have not had any
experience with this cleaning technology, it might take you a while to
get used to the specific vibration (tingling). However, most users say
that they got used to it quickly after a few uses and cleaning became
perfectly natural for them.
– Do not apply excessive pressure on your teeth.
– You can also use this brush when you have fixed braces, facets,
crowns, etc. However, please bear in mind that if the brush is used
with braces, the brush bristles are subject to more wear.
– We recommend that you replace the brush B with a new one after 3
months of use. However, if the brush is showing signs of significant
wear or damage.
+ mode switch
B2 – coloured ring to distinguish users
Caution
Notes
13 / 29
GB