Herunterladen Diese Seite drucken

GRAPHITE 59G718 Betriebsanleitung Seite 12

Vorschau ausblenden Andere Handbücher für 59G718:

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 14
Below are the explanations off numbers in each of the
figures at the beginning of this manual
Figure 1
1.
Base seat
2.
Depth indicator
3.
Cutting depth
4.
Fixing knob
5.
Adjusting screw
Figure 2
1.
Switch button
Figure 3
1.
Disassembly direction
2.
Assembly direction
3.
Keep
Figure 4
1.
Work piece
2.
Rotating direction of cutting bits
3.
Overlook from top
4.
Feeding direction
Figure 5
1.
Feeding direction
2.
Rotating direction of cutting bits
3.
Workpiece
4.
Parallel guide
Figure 7
1.
Base plate
2.
Screws
3.
Screwdriver
Figure 8
1.
Cutting bit
2.
Base plate
3.
Logo guider
4.
Work piece
5.
Guide bush
Figure 10
1.
Bolt
2.
Guide bar
3.
Parallel guide
4.
Wing nut
Figure 11
1.
Fixing screw
2.
Parallel guide
3.
Wing nut
4.
Base plate
Figures 13 and 14
1.
Wing nut
2.
Guide bar
3.
Parallel guide
4.
Center hole
5.
Bolt
Figure 15
1.
Nail
2.
Center hole
3.
Parallel guide
Figure 17
1.
Fixing nut (A)
2.
Adjusting nut
3.
Fixing nut (B)
4.
Bearing guide seat
Figure 18
1.
Work piece
2.
Cutting bit
3.
Bearing guide seat
1. Adjust the cutting depth
Screw out the fixing knob till loose. Adjust the base seat
assembly to your satisfied depth. Then screw the fixing
knob to be tightly (Fig 1).
2. Switch ON and OFF
To turn on the device, just turn the switch button to "I"
position. To turn off the tool, just turn the switch button to
"O" position (Fig 2).
3. Assemble and disassemble the bits
When assemble the bits, put the bit into the collet first, and
then use the two spanners to fix the clamping nut. Use the
spanners to disassemble the bits contrary procedure (Fig
3).
4. Reversing Switch Action
a) Put the tool onto the work piece in the way that the cutting
bits does not touch it. Turn on the tool. When the tool
achieves the full speed. Keep it moving forward to correct
direction. Make sure to keep the base plate trimly with the
working objects and keep the tool moving even speed (Fig
4).
WARNING: Moving the tools forward too fast will cause the
bad quality of work piece, damaging the cutting bits or
motor of the tool. Moving the tools forward too slow will
cause the cutting bits too hot and bad quality of work piece.
Before starting cutting, please try cutting firstly to some
wasted work piece. This will tell you the cutting quality and
then you could adjust the tool.
b) When using the parallel guide or guide bar, please make
sure to instal it onto the right hand of feeding direction.
Parallel bar and guide are for fine cutting of the tools (Fig
5).
WARNING: Feeding the tool too much will cause overload
of the motor. The maximum cutting depth of the tool is 3
mm. If you need depth more than 3 mm, you could achieve
it by cutting couple of times.
5. Guide bush
a) There is a guide bush in accessories. The cutting bit
could get through the guide bush cutting the work piece
according to logo (Fig 6).
b) Take down the base plate by loosen the screws. Put the
guide bush onto the base plate then fix back onto the tool.
Screw it tightly (Fig 7).
c) Fix the logo guider onto the work piece. Put the tool onto
the guider. Move the tool forward to cutting the work piece
according to the side line of the guider (Fig 8).
6. Parallel guide (optional accessory)
a) When cutting edge or groove of the work piece, the
parallel guide is quite useful (Fig 9).
b) Use the bolt and wing nut to assemble guide bar to the
parallel guide (Fig 10).
c) Use the fixing screw to assemble the parallel guide.
Screw out the wing nut on parallel guide. Adjust the
distance between the cutting bits and the parallel guide.
When achieving the proper distance, please fix the wing nut
tightly (Fig 11).
d) If the distance from the edge of work piece to cutting line
is too far, then you could not use the parallel guide. Under
such condition, please fix a straight plate onto the
workpiece tightly as a guide plate of cutting. Then move the
tool forward along the edge of this guide plate (Fig 12).
7. Cutting circle.
a) If you assemble the parallel guide a according to the Fig
12 and Fig 14, then you could cut the circle with the tool.
The cutting radius (the distance between cutting bits and
the center of circle):
Minimum Radius: 70 mm
Maximum Radius: 221 mm
b) If you want to cut the circle between 70 mm to 121 mm
radius, you could assemble the parallel guide according to
Fig 13.
c) If you want to cut the circle between 121 mm to 221 mm
radius, you could assemble the parallel guide according to
Fig 14.
d) You could no cut the circle between 172 mm to 186 mm
radius.
e) Put the center hole on the parallel guide onto the center
on work piece. Put a nail less than 6 mm to the center hole
to fix the parallel guide. Cutting the work piece by direction
of clock wise (Fig 15).

Werbung

loading