Siemens CE1G2264X Installationsanleitung Seite 6

13. Kontrola funkcí
g) Kontrola zobrazení. Pokud nesvítí žádné zobrazení,
zkontrolujte vložení a funkce baterií
h) Druh provozu: Komfortní
i) Nastavte žádanou teplotu
Teplota T (viz. Návod k obsluze)
j) Relé a řízená jednotka se musí sepnout do jedné
minuty. Na displeji svítí symbol
případě:
• zkontrolujte řízenou jednotku a připojení kabelů
• eventuálně je prostorová teplota vyšší než 29 °C
k) Žádanou teplotu
(standardní teplota 19 °C nebo vlastní nastavení)
l) Volba vybraného druhu provozu
Commissioning
1. Mounting
Remove controller from its base by proceed according to
Fig. A.
For mounting, refer to Figs. B and C and "Mounting notes".
2. Check wiring
For the electrical connections, refer to "Connection
diagram" (also refer to Figs. D and E).
Note: do not use stranded wires, only solid wires or
stranded wires with ferrules.
3. Remove the battery transit tab
As soon as the battery transit tab is removed, the controller
starts to operate (also refer to Fig. F).
4. Configuration
4.1 Accessing the heating engineer level
The heating engineer level will be enabled by pressing
simultaneously the warmer and colder buttons and by
rolling the roller selector away from the display and then
toward the display (also refer to Fig. H).
4.2 Functions
4.2.1 Calibrating the temperature sensor
After activating the heating engineer level, the CAL symbol
will flash. When pressing the roller selector, the room
temperature currently measured flashes and can now be
recalibrated by a maximum of ± 2 °C by rolling either
toward the display or away from it. To store the re-
calibration, press the roller selector (also refer to Fig.
4.2.2 Setpoint limitation
There are 2 setting choices available:
or
On the heating engineer level, change from the flashing
CAL symbol to the setpoint limitation symbol by rolling
toward the display.
Press to accept. 5...29 °C will flash (factory setting). Press
to accept or continue rolling.
Setting 16...29 °C will flash.
Press to accept.
6/9
na 29 °C v menu
. V opačném
vraťte opět na původní hodnotu
14. Pokyny
• REV23 je elektronický regulátor prostorové teploty
s týdenním spínacím programem.
• Regulátor patří do softwarové třídy A a je určen pro
použití v prostředí s normálním stupněm znečištění.
• Pokud se v refernční místnosti nacházejí termostatické
radiátorové ventily, musí být úplně uzavřeny.
• Kontakt dálkového ovládání musí být oddělený, příp.
připojen odděleným a odstíněným kabelem.
• Je nutné dodržovat místní předpisy pro elektrickou
instalaci.
4.2.3 Optimum start control
On the heating engineer level, change from the flashing
CAL symbol to the optimum start control symbols
(also refer to Figs.
Press to accept.
Press to accept or continue rolling until you reach ½, 1 or
optimization OFF
4.2.4 Control mode
On the heating engineer level, change from the flashing
CAL symbol to the symbols of the various control modes
by rolling away from the display (also refer to Fig.
Press to accept.
accept (Fig. 3) or continue rolling toward the display to
select one of the following control modes:
, PID 6, PID 12 or
required control mode.
A brief description of the control modes is given below
(also refer to Fig.
Self-learning, adaptive control:
Suited for all standard applications (factory
setting).
PID 12 Normal controlled systems:
For locations with normal temperature variations.
PID 6 Fast controlled systems:
For locations with significant temperature
variations.
).
Difficult controlled systems:
Proper on / off controller with a switching
differential of 0.5 C.
4.2.5 Periodic pump run
This function protects the pump against seizing during
longer off periods. Periodic pump run is activated for a
minute every 24 hours at 12:00 (when pump run is
activated, the flame symbol
On the heating engineer level, change from the flashing
CAL symbol to the
the display (factory setting, periodic pump run off). Press to
accept. will flash (factory setting). Press to accept or
continue rolling. The
will flash. Press to accept (also refer to Fig.
09.01.2002
by rolling twice toward the display
and ).
will flash (factory setting).
. Press to accept.
(factory setting) will flash. Press to
. Press to accept the
).
appears on the display).
symbol by rolling twice away from
symbol for periodic pump run on
CE1G2264X
).
).