Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Danger: Engage the chain brake slowly and ca-
refully. Hold the saw fi rmly with both hands, and
make sure you have a good grip. The saw must
not touch any objects.
7. The chain (3) must stop abruptly. Immediately
release the throttle lever (11) when the chain
(3) has come to a stop.
Danger: If the chain (3) does not stop, shut off
the engine and take the saw to an authorized ser-
vice center for repair.
6.1.2 Checking the clutch
Carry out a functional check on the clutch on a re-
gular basis. Test the clutch before the fi rst cut, af-
ter several cuts, after maintenance is done on the
chainsaw and if the chainsaw has been subjected
to strong impact or if it has been dropped.
1. Start the chain saw by following the starting
instructions. (refer to 6.2 and 6.3)
2. Briefl y actuate the throttle lever and release
it to ensure that the throttle valve has been
released and the engine is idling.
3. The chain (3) must stop when the engine is
idling. The clutch has been designed so that
when the idling speed is increased by a factor
of 1.25 no chain movement can be detected.
Danger: If the chain (3) does not stop, shut off
the engine and take the saw to an authorized ser-
vice center for repair.
Danger: Always engage the chain brake (6) befo-
re you start the engine.
6.2 Starting a cold engine (Fig. 7A-7E)
Fill the tank with an adequate amount of gasoline/
oil mix. (refer to Paragraph 5.3)
1. Set the equipment down on a hard, level sur-
face.
2. Move the On/Off switch (10) to the „I" positi-
on. (Fig. 7A)
3. Press the fuel pump primer (23) 10 times.
(Fig. 7B)
4. Pull out the choke lever (13) (Fig. 7C)
Note: Pulling out the choke lever (13) opens the
throttle valve slightly and locks it in that position.
This increases the idle speed, and the saw starts
faster.
Anl_GC_PC_730_I_SPK7.indb 26
Anl_GC_PC_730_I_SPK7.indb 26
GB
5. Hold the saw fi rmly and pull out the starter
handle (9) until you feel it start to resist. Then
sharply pull the starter handle 3 times. (Fig.
7C/7D)
6. Push in the choke lever (13).
7. Hold the saw fi rmly and pull out the starter
handle (9) until you feel it start to resist. Then
quickly pull the starter handle (9) several
times until the engine starts. (Fig. 7D)
Note: Do not allow the starter handle (9) to snap
back. This may result in damage. Once the engi-
ne has started, allow the saw to warm up for 10
seconds.
Warning: Since the throttle lever is slightly open,
the cutter starts to operate when the engine is
started. Briefl y actuate the throttle lever (11). This
releases the throttle valve and the engine returns
to idle mode. (Fig. 7E)
8. If the engine does not start up after the starter
handle is pulled 8 times, repeat steps 1-7.
Please note: If the engine does not start up even
after several attempts, read the Engine trouble-
shooting section.
Please note: Always pull the starter handle out
straight. If it is pulled out at an angle, friction will
occur on the eyelet. As a result of this friction, the
cable will become frayed and will wear faster. Al-
ways hold onto the starter handle when the cable
retracts. Never allow the starter handle to snap
back when it has been pulled out.
6.3 Starting a warm engine (Fig. 7A-7D)
(The chainsaw has been idle for less than 15-20
min.)
1. Set the equipment down on a hard, level sur-
face.
2. Move the On/Off switch (10) to the „I" positi-
on. (Fig. 7A)
3. Press the fuel pump primer (23) 10 times.
(Fig. 7B)
4. Hold the saw fi rmly and pull out the starter
handle (9) until you feel it start to resist. Then
quickly pull the starter handle (9) several
times until the engine starts. The equipment
should start after 1-2 tugs. If the saw does not
start after 6 pulls, repeat steps 1 - 7 of Para-
graph 6.2. (Fig. 7D)
- 26 -
05.06.2019 08:26:41
05.06.2019 08:26:41
Werbung
