Werbung
Verfügbare Sprachen
Verfügbare Sprachen
18 | English
Cordless drill/driver
Recommended ambient temperature during
charging
Permitted ambient temperature during opera-
C)
tion
and during storage
Recommended rechargeable batteries
D)
Recommended chargers
A) Measured at 20−25 °C with rechargeable battery PBA 18V 2.5Ah W-B.
B) Depends on battery in use
C) Limited performance at temperatures <0 °C
D) The following chargers are not compatible with the PBA rechargeable battery: AL 1814 CV, AL 1820 CV, AL 1860 CV
Noise/Vibration Information
AdvancedDrill 18
Noise emission values determined according
to EN 62841-2-1.
Typically, the A-weighted sound pressure level of the power
tool is less than 70 dB(A). The noise level when working can
exceed the volume stated. Wear hearing protection!
Total vibration values ah (triax vector sum) and uncertainty K
determined according to EN 62841-2-1, EN 62841-2-2:
2
Drilling in metal: a
< 2.5 m/s
, K = 1.5 m/s
h
2
Screwdriving: a
< 2.5 m/s
, K = 1.5 m/s
h
AdvancedImpact 18
Noise emission values determined according to
EN 62841-2-1.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 85 dB(A); sound power level
96 dB(A). Uncertainty K= 5 dB.
Wear hearing protection
Total vibration values ah (triax vector sum) and uncertainty K
determined according to EN 62841-2-1, EN 62841-2-2:
2
Drilling in metal: a
< 2.5 m/s
, K= 1.5 m/s
h
2
screwdriving: a
< 2.5 m/s
, K= 1.5 m/s
h
impact drilling in concrete: a
= 19, K= 1.5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
1 609 92A 5W6 | (31.07.2020)
°C
°C
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Fitting
Battery charging
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
2
;
your power tool.
2
.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Do not continue to press the On/Off switch after the
u
2
;
power tool has automatically switched off. The battery
2
;
can be damaged.
2
.
Removing the battery
To remove the battery , press the battery release button and
pull the battery to the rear and out of the power tool. Do not
use force to do this.
Battery charge indicator
When the on/off switch (14) is pressed in halfway or com-
pletely, the battery charge-control indicator (13) indicates
the charge condition of the battery for several seconds. The
indicator consists of three green LEDs.
AdvancedDrill 18
AdvancedImpact 18
0 to +35
–20 to +50
PBA 18V...W-.
AL 18...
0 to +35
–20 to +50
PBA 18V...W-.
AL 18...
Bosch Power Tools
Werbung
