Werbung
Verfügbare Sprachen
Verfügbare Sprachen
OBJ_BUCH-1269-006.book Page 14 Thursday, August 4, 2016 1:32 PM
14 | English
Straight grinder
Spindle collar dia.
– with rubber cap
– without rubber cap
Grinding tool diameter, max.
Thickness of grinding wheels, max.
Polishing tool diameter, max.
Constant electronic control
Speed preselection
Weight according to EPTA-Procedure
01:2014
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Sound emission values determined according to EN 60745-2-23.
GGS ...
Typically the A-weighted noise levels of the product are
Sound pressure level
Sound power level
Uncertainty K
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K determined
h
according to EN 60745-2-23:
Surface grinding (with wheel diameter of 25 mm):
a
h
K
Vibration total values a
(triax vector sum) and uncertainty K determined
h
according to EN 60745-2-23:
Surface grinding (with wheel diameter of 50 mm):
a
h
K
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
1 609 92A 2JZ | (4.8.16)
GGS ...
8 CE
28 C
mm
–
–
mm
–
–
mm
50
50
mm
–
–
mm
80
–
–
kg
1.7
1.4
/II
/II
Assembly
Before any work on the machine itself, pull the mains
plug.
Mounting the Grinding Tools (see figure A)
Only use properly fitting and undamaged open-end
spanners (see "Technical Data").
– Clean the grinder spindle 3 and all parts to be mounted.
– Hold the grinder spindle 3 with open-end spanner 8 by the
spanner flats .
Loosen the clamping nut 2 with open-end spanner 9 by ap-
plying it to the spanner flats and turning in anticlockwise
direction.
– Insert the clamping shaft of the grinding tool to the stop in-
to the collet chuck 1.
– Hold the grinder spindle 3 firmly with open-end spanner 8
and clamp the tool bit with open-end spanner 9 by the
spanner flats , turning in clockwise direction.
28 CE
28 LC
28 LCE
–
–
–
–
–
–
50
50
50
–
–
–
–
–
–
–
1.4
1.6
1.6
/II
/II
/II
28 C
28 LC
8 CE 28 LP
28 CE
28 LCE
dB(A)
78
77
82
dB(A)
89
88
93
dB
3
3
3
2
m/s
3
6
≤2.5
2
m/s
1.5
1.5
1.5
2
m/s
8
14
≤2.5
2
m/s
1.5
1.5
1.5
Bosch Power Tools
28 LP
38
34
40
32
–
–
1.7
/II
80
91
3
6
1.5
20
1.5
Werbung
