Bosch GAS 35 L AFC Professional Originalbetriebsanleitung Seite 18

OBJ_BUCH-1746-001.book Page 18 Thursday, February 14, 2013 2:58 PM
18 | English
Noise Information
Measured sound values determined according to EN 60704.
Typically the A-weighted sound pressure level of the vacuum
cleaner is lower than 70 dB(A). Uncertainty K= 3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical data" is in conformity with the fol-
lowing standards or standardization documents: EN 60335
and the directives 2011/65/EU, 2006/42/EC,
2004/108/EC including their amendments.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider Helmut Heinzelmann
Senior Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
15.02.2013
Assembly
 Before any work on the vacuum cleaner itself, pull the
mains plug.
Mounting the Vacuum-hose Holder (see figure A)
– Slide the vacuum-hose holders 5 firmly from above into the
retainers 30 intended for this purpose, until they engage.
Mounting the Vacuum Hose (see figure B)
– Mount the vacuum hose 21 onto the hose connection
piece 2 and turn it in clockwise direction to the stop.
Note: While vacuuming, an electrostatic charge develops in
the vacuum hose and accessories caused through the friction
of the dust, which the operator could experience in the form
of static discharging (dependent on environmental influences
and physical perception).
As a general rule, Bosch recommends using an anti-static vac-
uum hose (accessory), when vacuuming fine dusts and dry
materials.
Mounting VAC Accessories (see figure C)
The vacuum hose 21 is equipped with a clip system, with
which the VAC accessories (tool sleeve 20, elbow 22) can be
connected.
Mounting the Tool Sleeve
– Mount the tool sleeve 20 onto the vacuum hose 21 until
both snap-fasteners 31 of the vacuum hose can be heard
to engage.
– To disassemble, press both snap-fasteners 31 inward and
pull the components apart.
1 619 929 L28 | (14.2.13)
Mounting Nozzles and Tubes
– Mount the elbow 22 onto the vacuum hose 21 until both
snap-fasteners 31 of the vacuum hose can be heard to en-
gage.
– Afterwards, mount the desired VAC accessory (floor noz-
zle, crevice nozzle, vacuum tube, etc.) firmly onto the el-
bow 22.
– To disassemble, press both snap-fasteners 31 inward and
pull the components apart.
Inserting/Removing a Disposal Bag or Dust
Bag (Dry Vacuuming) (see figures D1
For dry vacuuming, a disposal bag 23 or a dust bag (accesso-
ry) can be used. This makes the disposal of the dust easier.
Note: When using a paper filter bag, the automatic filter
cleaning (AFC) (see "Deactivating the AFC", page 20) must,
and when using a fleece filter bag, should be shut off.
Inserting a Disposal bBag
– Unlock the latches 11 and remove the vacuum lid 10.
– Insert the disposal bag 23 into the container 1 with the fill-
ing opening toward the front.
– Pull the filling opening over the connection flange into the
recess of the connection flange.
– Make sure that the disposal bag 23 faces completely
against the interior sides of the container 1.
– Fold the rest of the disposal bag 23 over the edge of the
container 1.
– Reattach the vacuum lid 10 again and lock the latches 11.
Removing and Closing the Disposal Bag
– Unlock the latches 11 and remove the vacuum lid 10.
– Pull the full disposal bag 23 toward the rear off of the con-
nection flange.
– Carefully remove the disposal bag 23 out of the vacuum
cleaner without damaging it.
When doing this, pay attention that the disposal bag does
not get caught or ripped open against the connection
flange or other sharp objects.
– Pull the cover off of the adhesive strip, close the disposal
bag and tape it shut.
Afterwards, tie off the disposal bag 23 below the filling
opening with the pulled off cover of the adhesive strip.
Replacing/Inserting the Dust Bag (Accessory)
– Unlock the latches 11 and remove the vacuum lid 10.
– Pull off the full dust bag from the connection flange toward
the rear. Close the opening of the dust bag by folding down
the lid. Remove the closed dust bag from the vacuum
cleaner.
– Work the new dust bag over the connection flange of the
vacuum cleaner. Make sure that the dust bag faces com-
pletely against the interior sides of the container 1 over its
full length.
– Reattach the vacuum lid 10 again and lock the latches 11.
Inserting the Rubber Lip (Wet Vacuuming)
(see figure E)
Note: The requirements for the ingress degree (dust
category L) have only been proven for dry vacuuming.
D2)
–
Bosch Power Tools