Park Tool AK-40 Advanced Betriebsanleitung

Park Tool Co.
5115 Hadley Ave. N. St. Paul, MN 55128 (USA) www.parktool.com
For detailed instructions on a
variety of maintenance and repair
procedures: www.parktool.com
AWS-1, AWS-3 and TWS-3 3 Way Wrench Sets
Used to install and adjust brakes, derailleurs, saddles,
seat posts, handlebars, bottle cages, etc., the AWS-1
(4, 5, 6mm), AWS-3 (2, 2.5, and 3mm) and TWS-3 (T10,
T25, T30) are favorites of professional and home me-
chanics worldwide.
BBT-22 and BBT-9 Bottom Bracket Tools
Park Tool Bottom Bracket Tools are used to install
and remove bottom bracket cups. The BBT-22 fits Shi-
mano Octalink and ISIS Drive 20-tooth, splined bottom
bracket cups. The BBT-9 fits 16-notch external bearing
bottom bracket cups from Shimano, SRAM, FSA, Cam-
pagnolo, Race Face, and others. It also engages the 8
internal splines of the crank arm adjustment cap used
on Shimano Hollowtech II systems.
Bottom Bracket Cup Removal:
1. Fit bottom bracket tool into non-drive side cup and
turn counterclockwise with wrench until removed.
2. Fit bottom bracket tool into drive side cup and turn
clockwise with wrench (counterclockwise for Ital-
ian threaded cup) until removed.
Bottom Bracket Cup Installation:
1. Fit bottom bracket tool into drive side cup and turn
counterclockwise with wrench until tight (clock-
wise for Italian threaded cup).
2. Fit bottom bracket tool into non-drive side cup and
turn clockwise with wrench until tight.
© 2015 Park Tool Co. / PARK TOOL® and the color BLUE are registered trademarks of Park Tool Co. All other referenced trademarks and trademark registrations are the property of their respective owners.
BO-2 Bottle Opener
The BO-2 is engineered
to provide tremendous
leverage, making quick
work of any bottle cap.
CC-3.2 Chain Wear Indicator
A worn chain shifts poorly and wears sprockets at an
accelerated rate. The CC-3.2 is a "go/no-go" gauge de-
signed to accurately indicate when a chain reaches .5%
and .75% wear, the points at which most manufacturers
suggest replacement (contact the chain manufacturer
for specific replacement recommendations).
Instructions:
One side of the CC-3.2 is used to check for chain
wear at the .5% level; the other side is used to check
for chain wear at the .75% level. Select correct side
and lower CC-3.2 onto chain. If gauge tip fits com-
pletely into chain link (Figure 1), the chain is worn
and should be replaced. If gauge tip does not fit into
link (Figure 2), the chain is not worn and does not re-
quire replacement.
CL-1 Synthetic Blend Chain Lube with PTFE
Using a proprietary blend of oils and PTFE, CL-1 works
great in wet or dry conditions. It penetrates, reduces
friction, prolongs component life, displaces moisture,
and protects parts from rust and corrosion. Apply a
drop to the inside of each chain link; then wipe off ex-
cess with a rag. Also works great on brake and derail-
leur pivot points.
CM-5.2 Cyclone Chain Scrubber
The Cyclone Chain Scrubber cleans bicycle chains
quickly, easily, and effectively without the hassle and
mess of removing the chain from the bike. Regular use
improves shifting performance and extends the life of
the chain and other drive train parts.
AK-40 Advanced
Mechanic Tool Kit
Instructions:
1. Place newspaper or other floor protection under work
area. Remove excess mud and grime from chain and
other components with GSC-1 GearClean Brush and/
or a rag. Shift chain to smallest sprocket in the back.
2. Attach Cyclone around lower section of chain.
3. Fill Cyclone with cleaning fluid to fill line. Park Tool
CB-2 Citrus ChainBrite is recommended. Do not
use gasoline, petrol, kerosene or other volatile or
flammable solvents.
4. Crank pedals backwards 30 revolutions.
5. Empty Cyclone and rinse with water. Squeeze fluid
from sponge.
6. Repeat steps 2–5.
A replacement brush and sponge kit is available from
your favorite retailer (Part # RBS-5).
CN-10 Cable and Housing Cutter
The CN-10 Cable and Housing Cutter is a shop quality
cutter designed specifically for use on bicycle cables
and housing. Includes a built-in crimper for both cable
end caps and housing ferrules.
Adjustment Instructions:
As the CN-10 wears it may require readjustment for
best cutting results.
1. Turn nut counterclockwise to loosen. To tighten
adjustment, turn bolt clockwise. To loosen, turn
counterclockwise.
2. Turn nut clockwise to tighten.
Repeat as needed until tool cuts cleanly and handles
operate smoothly.
CNW-2 Chainring Nut Wrench
The CNW-2 makes chainring bolt set installation and
removal easy. It securely holds the slotted nut to pre-
vent spinning when tightening or loosening the bolt.
Double-ended to fit most slotted-type nuts.