Werbung
Verfügbare Sprachen
Verfügbare Sprachen
INTENDED USE
This right angle tool is designed for use with 7" diameter coated abrasive discs of various grades of grit which are designed to be used at the same or higher
speed of the tool. The spindle thread is 5/8-11 UNC-2A and the tool can be used with other abrasive devices that have the same female thread size and are
designed to run without a guard and have a rated speed equal to or higher than the speed of the tool. Do not attempt to use any bonded abrasive devices,
i.e. grinding wheels, as those which could be fitted because of their size, cannot be used without a suitable guard. A guard is not available for this tool. Do
not fit any form of saw blade. Do not fit any other abrasive or cutting device before checking the suitability for use with this tool with the manufacturer or the
manufacturer's authorized distributor.
AIR SUPPLY
The efficiency and life of this tool depend on the proper supply of clean, dry air at a maximum of 90 PSI. The use of an airline filter, pressure regulator, and
lubricator is recommended. Before connecting to tools, blow out the airline to remove water and dirt that may have accumulated.
HOSE AND HOSE CONNECTIONS
The air supply hose recommended is 3/8" (10mm) I.D. If an extension hose is necessary, use 1/2" (13mm) ID hose with couplings not less than 3/8" (10mm)
I.D. The tool inlet thread is 1/4" NPT.
LUBRICATION
All models may operate without airline lubrication. However, operating the tool without airline lubrication may reduce tool performance and vane life.
If an airline lubrication is not used, it is recommended that the tool be oiled daily before use to improve performance. Add 2-4 drops of air motor oil and run the
tool for 10-20 seconds to distribute oil through the tool.
For maximum performance and tool life, an air line lubricator, set to deliver 2 drops per minute, is recommended. SIOUX No. 288 Air Motor Oil is
recommended.
Do not over lubricate because excess oil may contaminate the surface being sanded.
For Angle Head
Lubricate the angle head assembly with 2 shots of SIOUX #1232 grease every 8 working hours.
MAINTENANCE
Water, dust and other airline contaminants can cause rust and vane sticking. For long periods between tool use, flush the tool with a few drops of oil and run
for 10 seconds. This will help remove contaminants and reduce the formation of rust.
OPERATION
The tool is equipped with a locking type lever in order to prevent accidental start-up.
Select a suitable abrasive disc and make sure it is fixed securely to the tool. Connect to suitable air supply as recommended. Make sure that the side handle is
tightened securely. Apply the sander lightly to the work and allow the abrasive disc to cut.
INSTALLING SANDING DISC (5/8"-11 Thread Models)
•
Thread backing pad onto spindle.
•
Place sanding disc over spindle and seat against backing pad.
•
Thread disc retainer onto spindle and tighten
SPECIFICATIONS
• Recommended Air Pressure
• Air Consumption
• Air Inlet Thread Size
• Recommended Hose Size
• Spindle Thread
• Pad Size
Free Running
Catalog
Speed
Number
RPM
5287C
6,000
Form ZCE883
Always remove the tool from the air supply be for installing or changing sanding discs!
90 psig (620 kPa)
35 scfm
1/4-18 NPT
3/8" (10 mm) x 30' (10 m)
5/8"-11UNC
7" (180 mm)
Backing Pad
Specifications at 90 psig (6.2 bar, 620 kPa)
Length
Weight
in
lb
(mm)
(kg)
*Sound
Pressure
(dBA)
12.6
4.4
80.5
(320)
(2.0)
WARNING
Disc Retainer
Noise* (Tested in accordance with
ISO Standard 15744)
Uncertainty, K
*Sound Power
(dBA)
(dBA)
3.0
91.5
4
Handle
Throttle Lever
Vibration*
(Tested in accordance with
ISO Standard
Uncertainty
*Vibration m/s
(dBA)
3.0
4.9
Date 2023October4/A
Inlet Bushing
28927-1)
Uncertainty
2
m/s
2
0.98
Werbung
