Werbung
Verfügbare Sprachen
Verfügbare Sprachen
by turning the first nozzle control as
shown in the figure (Fig. 27).
– Also, the nozzle can change the angle
of the foam spray jet by turning the
nozzle control knob as shown in the fig-
ure (Fig. 28).
– When applying the foam, the noz-
zle should be located at a distance of
about one meter from the surface.
– Apply the foam horizontally, from side
to side, starting from the bottom of the
surface.
– There is no need to apply the foam sev-
eral times to the same area.
– After the foam has worked, rinse it off
with water, from top to bottom. Keep
the nozzle at least 30 cm away from the
surface.
– After using the foam nozzle, it is import-
ant to rinse the foam nozzle complete-
ly. To clean, fill a container with clean
water and spray. This way, the nozzle is
ready for the next use.
Turbo nozzle for cleaning surfaces
PW-18Ri (2021)
Insert the Turbo Nozzle into the clutch of
the Spray Gun Extension Nozzle, it will
lock automatically. To remove the nozzle,
pull the clutch while gently holding the
nozzle (Fig. 29).
The turbo nozzle can remove stub-
born dirt, for example, on paving stones
(Fig. 30).
It is not recommended to use the turbo
nozzle for washing a car or delicate items
(Fig. 31).
Using interchangeable nozzles
Insert the nozzle into the clutch of the
spray gun extension, it will lock automat-
ically (1) (Fig. 32). To replace the nozzle,
pull the clutch, making sure to hold the
nozzle with your finger to prevent it from
being thrown off by excessive pressure
(2) (Fig. 32).
The nozzles are divided into five types
depending on the required spray angle:
40°, 25°, 15°, 0°, and a car shampoo noz-
zle (Figure 33).
EU-PW0923001-0923001
Using a foaming nozzle
PW-14B (2021), PW-16B (2021),
PW-16BR (2021)
Foaming nozzle mixes the detergent and
water together to better wash the sur-
face, while the density of the foam can
be adjusted. The foam should be left on
the surface for some time to dissolve the
adhering dirt. After washing off the foam,
most of the dirt that could damage the
paint by hand washing is removed. The
foaming nozzle does not leave behind
spills and traces, as it can be when work-
ing with a built-in tank.
The foaming nozzle can change the spray
angle from horizontal to vertical.
A thick layer of foam can remain on the
surface of the car for several minutes
without slipping. This gives it the op-
portunity to have an effect on pollution
and remove it from the surface. Using the
foaming nozzle (Fig. 51):
Pour foaming agent, having mixed it ac-
cording to the necessary technology (ac-
cording to the instructions for the deter-
gent), into the container of the foaming
agent (1).
Screw the foaming nozzle (2) with the
container (1) and install it in the cleaning
gun (3) with a little force and turn clock-
wise until the two parts are connected
(Fig. 51).
When applying foam, the nozzle should
be located at a distance of about one me-
ter from the surface.
Apply the foam horizontally, from side to
side, starting from the bottom of the sur-
face.
There is no need to apply foam to the
same area several times.
After the action of the foam, wash it off
with water, from top to bottom. Hold the
nozzle at a distance of at least 30 cm from
the surface. After using the foaming noz-
zle, it is important to rinse it completely.
To do this, pour clean water into the con-
tainer and spray. Thus, the nozzle will be
ready for the next use.
To prevent the foam generator from ro-
tating around its axis, it is necessary to
move the slider on top of the cleaning
gun (Fig. 52).
en
17
Werbung
