Werbung
Verfügbare Sprachen
Verfügbare Sprachen
en
WARN ING!
Attention: it is recommended to
use the pressure washer with active
foam TM "DNIPRO M" CF-81. The use
of other cleaning agents or chemi-
cals may adversely affect the tech-
nical condition and overall service
life of the pressure washer.
WARN ING!
Do not spray flammable liquids near
hot objects, open flames, etc. –
there is a risk of explosion and fire.
Using the built-in cistern
The built-in tank is located at the bot-
tom of the back of the pressure washer
(Fig. 23). Open the rubber tank cap and
pull out the hose and fill the tank with
cleaning agent. If necessary, use a water-
ing can (not included). Close the rubber
tank lid tightly.
Insert the detergent nozzle (black nozzle)
into the spray gun extension (Fig. 24). Us-
ing the detergent flow control switch, set
the desired amount of detergent by ad-
justing from MIN to MAX (Fig. 25). To rinse
off the detergent, turn the detergent flow
control to the counterclockwise MIN po-
sition and set the nozzle to 15˚ or 40˚.
WARN ING!
Always read the detergent instruc-
tions carefully and follow the in-
structions for application methods
and the time the detergent must re-
main on the surface to be cleaned.
Work with the detergent in a venti-
lated area. Follow the recommend-
ed concentration. In case of contact
with skin or eyes, rinse immediately
with plenty of water and seek med-
ical advice if necessary. Keep out of
the reach of children!
When you are finished, empty the remain-
ing detergent from the tank. To do this,
remove the rubber cap from the tank and
pull out the filter hose. Disconnect the
tank from the pressure washer and empty
the residue. Rinse the detergent tank af-
16
ter each use. In the event of a spill, unplug
the appliance and wipe up the detergent.
Using the foaming nozzle
PW-18Ri (2021)
The foaming nozzle mixes detergent and
water together to give the surface a bet-
ter clean, and the foam density can be
adjusted. The foam stays on the surface
for a while, dissolving stuck-on dirt. After
the foam is rinsed off, most of the dirt that
could damage the paint during manual
washing is removed. The foaming nozzle
does not leave streaks and marks, as can
be the case with car shampoo sprayed
from a built-in tank.
The principle of operation of the foaming
nozzle is quite simple: it works by passing
water through the narrowing channel and
mixing with the detergent.
The foaming nozzle has a mixing valve
that allows you to control the ratio of de-
tergent to water, creating thicker and
thinner foam.
The foaming nozzle can change the spray
angle from horizontal to vertical.
A thick layer of foam can remain on the
surface of the car for several minutes
without slipping off. This gives it the op-
portunity to act on dirt and lift it off the
surface.
Use the foaming nozzle:
•
Unscrew the foaming agent con-
tainer clockwise (1) and pour the pre-
pared foaming agent into the foaming
agent container (2) (Fig. 26). Alternative-
ly, you can add it last to prevent the solu-
tion from foaming ahead of time, when
pouring water. Then, after screwing the
foaming agent container to the nozzle,
the solution will need to be shaken. You
can also add water the other way around:
first add the product, and then slowly
add water with a little pressure. This way,
the foaming agent will be mixed in the
process of pouring water.
– Screw the foaming agent container (1)
onto the nozzle, place the foaming noz-
zle into the cleaning gun (3) and screw
clockwise (4) (Fig. 26).
– The foaming nozzle can change the
spray angle from horizontal to vertical
EU-PW0923001-0923001
Werbung
