Operation; Maintenance - Triton TWX7 Gebrauchs- Und Sicherheitsanweisung

Module removal:
• Toggle the Module Locks (20) into the 'unlocked' position, Fig. G. Lift the module from the chassis using the Finger
Holes (23), and slide the Module Rollers (22) from the Module Mounting Tracks (21), see Fig. F
Note: Modules can be placed upright by angling them to around 120°. This position can be used, when adjustments
on the underside of modules are necessary, eg adjustments to the fitted power tools, there is no need to remove the
module.
Levelling table modules
• Level the module by adjusting the Module Levelling Bobbin Screws (27), and Module Levelling Screws (25) in the
order depicted in Fig. H
• Check the module is level against the surrounding chassis using a straight edge, as depicted in diagram Fig. I. If
the module is still uneven, repeat the above process
Electrical connections
Note: The Workcentre features a mains isolator switch with Trailing Socket (18), to allow easy connectivity to power
tools. This Socket may need to be removed to allow connection of some modules without a mains connector.
• Connect the Workcentre to the mains via the Mains Plug (19)
• Use the Trailing Plug to connect power tools to the power supply.
1. Power tools must be connected to the Workcentre switchbox
2. If necessary, suitable extension cords may be used to extend the Workcentre's own power cable
WARNING: Use only extension cords that are in good condition, with a sufficient cross section to carry the current the
power tool will draw. Undersized extensions will cause in-line voltage to drop, resulting in power loss, overheating and
burning out of the power tool motor.
Dust extraction
WARNING: ALWAYS use a suitable vacuum cleaner or workshop dust extraction system if dust containing
harmful substances is produced, e.g. when working with certain types of wood, painted or varnished workpieces,
workpieces with surface coatings etc. ALWAYS dispose of harmful dust according to laws and regulations.
Note: Most accessories used with the Triton Workcentre system are designed to be connected to a workshop dust
extraction system or a vacuum cleaner. This is the preferred and most effective method of dust extraction.

Operation

Workcentre switchbox operation
• The Workcentre ON/OFF Switch (10) is located at the front, behind the 'Knee-Off' Stop Button (11), see Fig. J
• Lift the 'Knee-Off' Stop Button to reveal the ON/OFF Switch, Ensure the switch is in the 'O' position
• Plug the Mains Plug (19) into a mains socket, to provide power to the Workcentre Power Socket
Switching on and off
• With the Workcentre connected, switch on the mains power supply
• Plug in the desired power tool to the Power tool Connection Socket (18)
• Switch on and provide power to Workcentre-associated tools by lifting the 'Knee-Off' Stop Button (11) and pressing
the ON/OFF Switch (10) into the 'I' position
• Switch off the power tool by pressing the ON/OFF Switch into the 'O' position. This can also be achieved by
pressing down the 'Knee-Off' Stop Button
Note: If the power supply is interrupted during use, the machine will not restart. The ON/OFF Switch will need to be
activated again to resume operation.
User position and feed direction
• The main user position is defined by the location of the 'Knee-Off' Stop Button (11)
• ALWAYS remain in close proximity to the switch to instantly switch the machine off in the event of an emergency
Troubleshooting For Clamping Table
Problem
Table module is not level
'Play' between table module and chassis
GB
5
Possible cause
Levelling screws are not correctly adjusted
Rough surface
Legs not correctly seated
Module levelling bobbins, not correctly adjusted
• Feed your workpieces from this position, in the direction indicated by the arrows on the table surface of the
individual module
Using the clamping holes
• The clamping table module features a series of 20mm diameter holes for the use of clamping devices, and bench
dogs
Using the table extensions (Available as accessories)
• The outfeed and side support bars can be adjusted to provide sturdy support to larger workpieces. Adjustability can
be performed by loosening the Outfeed Support Knobs (15), and/or the Side Support Knobs (4) and extending the
corresponding support bar to the size of the workpiece
Accessories
• A full range of Workcentre accessories and compatible Triton power tools, including Circular Saws and Precision
Plunge Routers, is available from your Triton stockist. Spares can be obtained from toolsparesonline.com

Maintenance

WARNING: ALWAYS disconnect the Workcentre from the power supply, before cleaning, changing accessories,
making adjustments or carrying out maintenance.
WARNING: ALWAYS wear protective equipment including eye protection and suitable, cut-proof gloves when
cleaning or carrying out maintenance.
General inspection
• Regularly check that all the fixing screws are tight. They may vibrate loose over time
• Inspect the supply cord of the tool, prior to each use, for damage or wear. Repairs should be carried out by an
authorised Triton service centre. This advice also applies to extension cords used with this tool, as well as cords of
the power tools installed in this Workcentre
Cleaning
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and shorten the device's
service life
• Clean the body of your machine with a soft brush, or dry cloth
• Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient, a mild detergent on a damp cloth is
recommended
• Water must never come into contact with the tool
• Ensure the tool is thoroughly dry before using it
• If available, use clean, dry, compressed air to blow through the ventilation holes (where applicable)
Lubrication
• Lubricate all moving parts with PTFE spray at regular intervals, especially after heavy use or cleaning
WARNING: DO NOT lubricate with oil or silicone-based maintenance sprays. Lubricant residue will combine with wood
and dust leading to dirt build-up interfering with moving parts and mechanisms. ONLY dry lubricate, using PTFE spray.
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
Disposal
Always adhere to national regulations when disposing of power tools that are no longer functional and are not viable
for repair.
• Do not dispose of power tools or other waste electrical and electronic equipment (WEEE), with household waste
• Contact your local waste disposal authority for information on the correct way to dispose of power tools
Using a spirit level, adjust the Module Levelling Screws (25) till the surface module is flat
Ensure the Workcentre is situated on a secure flat surface. Relocate the table if the ground is found to be rough
Follow instructions provided under 'Basic set-up', and ensure the legs are correctly seated and locked into place
Adjust Module Levelling Bobbin Screw (27) to remove 'play' in Workcentre module
Solution