Bosch GWS Professional HEAVY DUTY 18V-15 C Originalbetriebsanleitung Seite 36

36 | English
Always secure a grinding/cutting disc using only the
u
quick-clamping nut (21) supplied.
Press the spindle lock button (3) to
lock the grinding spindle. To tighten
the quick-clamping nut (21), fold up
the bar and turn the quick-clamping
nut firmly clockwise. Then fold down
the bar to secure the quick-clamping
nut. It is not sufficient to tighten the
disc along the edge.
Quick-clamping nuts (21) that are
properly secured and not damaged
can be removed by hand. To do this,
fold up the bar and turn the quick-
clamping nut firmly anticlockwise. If
the quick-clamping nut is stuck, do not
attempt to loosen it with a tool – al-
ways use a two-pin spanner.
After fitting the mounting flange and
the grinding/cutting disc, the free
thread length of the grinding spindle
must be at least 4 mm.
Ensure that the abrasive tool is firmly seated, so that it does
not twist away from the spindle in the runout of the power
tool.
A plastic part (O-ring) is fitted around
the centring collar in the mounting
flange (17). If the O-ring is missing
or damaged, the mounting
flange (17) must be replaced before
operation can resume.
After fitting the abrasive tool, check that the abrasive
u
tool is fitted correctly and can turn freely before
switching on the power tool. Make sure that the abras-
ive tool does not brush against the protective guard or
other parts.
Approved abrasive tools
You can use all the abrasive tools mentioned in these operat-
ing instructions.
-1
The permissible speed [min ] or the circumferential speed
[m/s] of the abrasive tools used must at least match the val-
ues given in the table.
It is therefore important to observe the permissible rota-
tional/circumferential speed on the label of the abrasive
tool.
1 609 92A 8XH | (21.11.2023)
Max. [mm] [mm]
D b s
125 7.2 – 22.2
150 7.2 – 22.2
125 4.2 – 22.2
150 4.2 – 22.2
125 – –
150 – –
75 30 – M 14
125 24 – M 14
125 19 – 22.2
150 24 – M 14
150 19 – 22.2
125 – – M 14
83 – – M 14
125 6 10 22.2
s
150 6 10 22.2
α
125 21 – 22.2
Rotating the machine head (see figure F)
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
The machine head can be rotated in 90° increments. In this
way, the on/off switch can be brought into a more favourable
handling position for particular applications, e.g. for left-
handed tool users.
Completely unscrew the four screws (➊). Rotate the ma-
chine head carefully, without removing it from the hous-
ing, into the new position (➋). Screw in and retighten the
four screws (➌).
Dust/Chip Extraction
Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
[°]
-1
d α [min ] [m/s]
– 11,000 80
– 8500 80
– 11,000 80
– 8500 80
– – 11,000 80
– – 8500 80
– 11,000 80
– 11,000 80
– 11,000 80
– 8500 80
– 8500 80
– 11,000 80
– 11,000 80
> 0 11,000 80
> 0 8500 80
– 11,000 80
Bosch Power Tools