Anker A2573 Kurzanleitung Seite 2

EN
LED Indicator Status
Solid blue for 3 seconds, then off Connected to power
Solid blue Charging mobile device
Flashing blue Metal or abnormal objects detected
Overvoltage protection, indicating you need
Flashing green
to switch to a 12V
• You cannot charge your device wirelessly in these scenarios:
using a case with a magnetic/iron plate;
T
O
using a case with a pop socket;
O
using an ultra-thick (> 5 mm) protective phone case.
O
• Do not place any foreign objects between your device and the
wireless charger's surface, including metal pads on a car mount, credit
cards, door keys, coins, metal, or NFC cards, which will make wireless
charging fail or cause overheating.
• Wireless chargers make charging more convenient than wired
chargers, but confined by current wireless technology, their charging
speed is slower than that of wired chargers.
• High temperatures will reduce charging speed and restrict power,
which is a phenomenon common to all wireless chargers. It is
recommended that you charge your device in environments with
temperatures below 25°C / 77°F.
• Both the protective phone case and the position of your device on the
wireless charger will affect the charging speed. The farther it is placed
from the center of the wireless charger, the slower the charging speed
will be.
Important Safety Instructions
• Avoid dropping.
• Do not disassemble.
• Do not expose to liquids.
• For the safest and fastest charge, use original or certified cables.
• This product is suitable for moderate climates only.
• The maximum ambient temperature during use of this product must not exceed
40°C.
• Open flame sources, such as candles, must not be placed on this product.
01
• Only use a dry cloth or brush to clean this product.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for
3A DC adapter a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: (1) Reorient or relocate the
receiving antenna. (2) Increase the separation between the equipment and receiver.
(3) Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected. (4) Consult the dealer or an experienced radio / TV
technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance of 20 cm between the radiator & your body.
Product Name: PowerWave 10 Stand with 2 USB-A Ports
Model: A2573
This device complies with RSS-216 of Industry Canada. Operation is subject to the
condition that this device does not cause harmful interference.
RSS-Gen Issue 5 March 2019 "&" RSS-Gen numéro 5 mars 2019
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada's licence-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Any changes or modifications not expressly approved by the party responsible for
02