Texas BCU52M Bedienungsanleitung Seite 15

Assembly
Mount the handle as shown in Fig 2A. Ensure that
the machine is in balance and bolts are tighten.
Attach the middle tube to the machine, fasten with
butterfly knob. See fig 2B.
Attaching the:
Pruner
C. Attach the pruner to the middle tube and
fasten. See Fig. 2B.
To mount the bar and chain, see Fig. 11.
Pay attention that the chain is facing the right
way (see arrow)!
To loosen/tighten the chain, the adjustment
screw in front of the saw is used. See Fig. 12.
It is recommended to check and add chain
oil every 30-45 min.
Hedge trimmer
D. Remove the protection cap from the hedge
trimmer unit. Attached the tube into the hedge
trimmer. See the small hole on tube to know
which direction goes in. Tighten the screw.
Attach the hedge trimmer to the engine unit
and fasten. See Fig. 2B.
The hedge trimmer tube can be placed in a
transport angle by loosening a screw (see Fig.
2C). When the hedge trimmer is being used,
the tube must be turned back in work-position
(see Fig. 2D) and the screw must always be
tighten again before use.
Brush cutter and Grass trimmer
E/F. Attach the Brush cutter and Grass trimmer to
the machine and fasten. See fig 2B.
Use of accessories
Pruner
•
Do not use the saw (pruner) standing on a
ladder or another aid in unstable position.
•
Beware of falling branches.
Hedge trimmer
•
Hedge scissors may be used not only on
hedges but also to cut shrubs.
•
The best cutting output may be obtained when
the scissors are conducted at an approximate
angle of 15°to the hedge.
•
To obtain an even height of the hedgerow, it is
recommended to have a conducting cord
stretched along the hedge.
•
Side surface area of the hedge will be trimmed
by arched movements from down and upwards.
•
Clean the unit after every use and check all the
integrated tools and protection devices for
damages.
All manuals and user guides at all-guidesbox.com
Brush cutter and Grass trimmer
•
When the engine is stopped the rotating blade
must be held in grass or bush until it holds still.
•
Always hold the machine with both hands.
•
The machine must not be used if the safety
guard is not correctly fitted and in mint
condition.
•
Always stop the engine before attempting to
remove objects that may have stuck on the
blade.
•
Never touch or try to stop the blade while it is
still spinning.
•
A rotating blade may cause damage, as it
continues to spin after the engine has stopped
or the gas has been turned off. Always be in
control of the tool until the blade has stopped
spinning.
•
Always make sure that the blade is mounted
securely and correctly before every time it is
used.
•
Only use a sharp blade. Replace blades that
are worn or damaged.
•
Only use original spare parts.
•
Only use the blade for weeds, grass and
similar.
•
Kickback is something that may occur when
the rotating blade gets into contact with
something, it cannot cut. This contact may
have the effect, that the blade stops for a
moment, and suddenly the tool is thrown away
from the hard object that was hitting. This
reaction may be so violent that the user loses
control of the tool. Kickback may occur without
warning if the blade is stuck, loses speed or
impeded. This is most likely in areas where it is
difficult to see the material that is being cut.
•
The harness must always be used and
adjusted to fit in the correct manner.
•
Keep a firm grip on both handles while the
blade is running. Keep the blade away from
your body and below your waist.
Changing from trimmer to brush cutter
Dismounting the trimmer head See Fig 4B
1. Fit the Allen key (2) in the hole of the gear (3)
to lock the gear in place.
2. Turn and remove the trimmer head (1) from
the shaft.
3. Washers can now be removed.
Notice: Keep the parts for the trimmer head
together for later use.
Mounting of blade. See Fig 4A
1. Fit the Allen key (2) in the hole of the gear (3)
to lock the gear in place.
2. Fit the washer (7), blade (1), washer (6) and
the holder (5) onto the axle.
3. Fit the nut (4). Fasten tightly anticlockwise.
Make sure the blade is securely fasten.
15