Werbung
Verfügbare Sprachen
Verfügbare Sprachen
. The dishwasher has been
thoroughly tested at the factory.
A few small water spots may remain.
They will disappear with the first use.
. If your dishwasher is a especially designed
model for installation under a worktop
(built-in model), but will be used as
a free standing unit with
a supplementary
worktop, it must be secured so as not
—
to tip over. It can be secured to the wall
or adjacent kitchen unit.
. Disconnecting appliance.
— Pull out the plug.
- Turn off water tap.
- Detach hoses from tap
and drainage pipe.
— Unscrew mounting screws
under the work plate.
— Dismount base plate, if present.
— Pull appliance out,
so that the hoses drag behind.
. To transport appliance, ensure that it is
placed either in upward position of flat on
its back. If transported otherwise, any
residual water found in the appliance may
get to the control units and adversely
influence the functioning of the
programmes.
. For comparative purposes only.
Arrangement according to: DIN 44 990
Capacity: 12 place-settings
Arrangement example: Fig. @ and &
Comparative programme: Normal 65 °C.
Amount of dish-washing cleanser used
in the test-study: 25 g.
. Only for U.K. Electrical requirements
Check that the voltage stamped on the
rating plate which you will find under the
table top when you open the door
corresponds with your house electricity
supply which must be a.c. (alternating
current). Your machine is already fitted with
a plug incorporating a 13 A fuse. If it does
not fit your socket the plug should be cut
off from the mains lead and an appropriate
plug fitted. Throw away the cut off plug,
do not insert it in a 13 A socket elsewhere
in the house as this could cause a shock
hazard.
e@
Warning -
this appliance must be earthed.
Important
The wires in the mains lead are coloured in
accordance with the following code:
Green and yellow — Earth; Blue — Neutral;
Brown - Live
lf you fit your own plug the colours of the wires
in the mains lead of your machine may not
correspond with the markings identifying the
terminals in your plug in which case proceed
as follows:
The wire which is coloured green and yellow
must be connected to the terminal in the plug
which is marked with the letter E, or by the
earth symbol (+) or coloured green, or green
and yellow.
The wire which is coloured blue must be
connected to the terminal which is marked
with the letter N, or coloured black.
The wire which is coloured brown must be
connected to the terminal whieh is marked
with the letter L, or coloured red.
With alternative plugs a 15 A fuse must be
fitted either in the plug or adaptor or in the
main fuse box. In the event of replacing a fuse
in the plug supplied a 13 A ASTA approved
fuse to BS 1362 must be fitted.
If the plug is the moulded on type the fuse
cover must be refitted when changing the fuse.
In the event of losing the fuse cover, the plug
must no be used until a replacement fuse
cover has been obtained and fitted.
A new fuse
cover can be obtained from your nearest
Service Office or local Electricity Board. The
colour of the correct replacement fuse cover is
that of the coloured marks or insert in the
base of the plug.
Replacement of the mains lead
lf it is necessary to replace the mains lead for -
any reason (which should be only with another
of a suitable type) proceed as follows after
removing the plug from the socket.
Noting the positions of lockwashers and
differing type screws remove the plinth plate
and removing 4 screws. Remove the inner
insulating panel by removing the 2 screws and
slide it to the right to clear the slots. Slacken
the screw in the rear cable clamp.
Note routeing of cable, disconnect from
terminal block noting the position of the brown
(L) and blue (N) wires and earth point and
withdraw. Complete fitting of new cable by
reversing above steps.
27
Werbung
