Operation - Velleman VDPLDJBAR4 Bedienungsanleitung

• A DM MX terminator is
or is in an electricall
digita al control signal
resist tor between pin
devic ce in the chain.
Connect tion to the AC
The AC
separa
AC cor
• Simply insert the supp
suitable e wall outlet.
7. Op eration
Note: th e spot DIP switc
value e will have the s
highe est set switch w
7.1 Sta nd alone or
• The m master/slave op
mast ter device.
• Choo ose one VDPLDJ
[3] o of the next VDP
the la ast VDPLDJBA
• Conn nect the foot con
• Plug in the power ca
• Set t the master VDP
[A].
• When n mode is
• On a ll slave units, se
displa ay shows
(e.g. : addre
• To ch hange the speed
follow wed by the spee
desir red speed. Rang
7.2 DM X controlled
• Press s the MODE butt
[C]. The display now
• All D MX-controlled d
signa als. This digital s
the D DMX controller.
indiv idual address ca
• When n all devices hav
partic cular channel. I
simu ltaneously. If yo
numb ber. Changing t
• In ca ase of the 6-cha
(CH1 1~6), the second
• Use t the UP- [C] or D
follow wed by a digit (e
• Refer r to the table be
LEDs s are organized
white e LEDs (9), the
the o outer circle is fo
illust ration.
Note e: channel 1 con
spots s set to 2 and so
10.01.201 1
s recommended for installations
y noisy environ ment (e.g. disc
by electrical no oise. The DMX t
ns 2 and 3, whic ch is then plugg
Power Supply y
C socket providi ng power to the
tely earthed. D o not use any o
rd not authorize d by the manuf
plied AC power c cord into the po
ches [9] on the e back of each s
same output. Th hese spot DIP sw
will be applicable e.
master/slav ve (no DMX)
peration enables s that several de
JBAR4 that wil l act as a maste
PLDJBAR4 and so on. Make su
R4 (refer to §6 6 DMX-512 con
ntroller to the fo oot controller ja
ables [7] and pl lug the other en
PLDJBAR4 to
s selected, contr rol the sounds s
et the address t to 1. Select the
. Press the UP [ [C] or DOWN [B
ess = 16). Set th he address to 1
d of the internal l program, pres
ed (e.g. = speed 51). U
ge 1 – 100.
ton [A] until th e display [2] sh
w shows .
devices need a d digital start add
start address is the channel nu
The same starti
ing address can
an be set for ev very device.
ve the same ad dress, all the un
In other words: changing the se
ou set individua al addresses, ea
he settings of o one channel will
nnel VDPLDJBA AR4, you will h
d unit to 7 (1 + + 6) (CH7~12),
DOWN-button [ B] to select a D
e.g. : ad ddress = 16).
elow for an over rview of the ava
in circles and gr roups (see illust
second circle is formed by red
rmed by blue LE EDs (18). The g
ntrols all spots f for which the sp
o on.
VDPLDJ BAR4
s where the DM
os). The termin
terminator is sim
ed into the XLR
e VDPLDJBAR4
other AC cords t
facturer.
ower input [7] a
spot determine t
witches are stra
evices can be sy
er en connect its
re to plug a ter
nnection)
ack [6] of the m
nds into a suitab
(auto) or r (sound c
sensitivity with t
address setting
B] button; the d
using the UP [C
s the MODE but
Use the UP [C]
hows
ress so that the
umber from whic
n be used for a w
nits will "listen"
ettings of one c
ch device will "l
only affect the
ave to set the s
the third to 13
DMX starting ad
ailable DMX func
tration on page
LEDs (12), the
group number is
pot DIP switch [
5
X cable has to r run a long dista
nator prevents c corruption of the
mply an XLR plu ug with a 120Ω
R output socket [4] of the last
4 batten must b be properly and
han the one pro ovided or any ot
and insert the p ower plug into a
the output – spo ots set to the sa
aight forward (n not binary); only
ynchronized and d controlled by
s DMX output [4 4] to the DMX i
rminator into the e DMX output [4
master.
ble mains outlet t.
controlled) using g the MODE but
the sound sensi itivity knob [5]
g with the MODE E button [A]. Th
display shows followed by a
C] or DOWN [B B] buttons.
tton [A] until th he display show
or DOWN [B] b buttons to set th
or r , then pr ess the UP butt
e correct device responds to the
ch the device st tarts to "listen"
devices or an
whole group of
to the control s signal on one
channel will affe ct all devices
listen" to a sepa arate channel
device in quest tion.
start address of the first unit to
(7 + 6) (CH13~ ~18), and so on
dress. The disp lay shows
ctions per chann nel. Note that th
2). The inner m most circle are t
third circle are green LEDs (18
s indicated insid e the LEDs on t
9] is set to 1, c channel 2 for all
nce
e
ther
a
ame
y the
one
nput
4] of
tton
.
he
a digit
s
he
on
e
to
o 1
.
he
the
8) and
the
©Vellema an nv