Werbung
Verfügbare Sprachen
Verfügbare Sprachen
plies may void your warranty.
- Gently
For this model, we recommend
an
tire
LGB power supply with a power
- Use a small, straight-blade
output of 1 amp or more. For more
ewdriver to gently pry the new
information on LGB power sup-
traction tire into the wheel groo-
plies for indoor, outdoor and multi-
train operation,
see the LGB cata-
- Make
log.
completely in the wheel groove.
Attention!
After extended
opera-
Replacing
tion, this model may leave a small
The gearbox must be removed to
amount
of carbon
dust around
the
replace the motor (Fig. 6):
track. This dust can stain carpet
- Remove
and
other
materials.
The
user
joining
assumes full responsibility for any
connecting
damage.
wheels. Pull the drive rods away
from
MAINTENANCE
- There
Attention!
Improper service may
bottom of the gearbox. Counting
void
your
warranty.
For factory
from
authorized
service,
contact
an
second
authorized
retailer
or
send
this
- Pull the gearbox away from the
product to an LGB service station
(see Factory Service).
chassis.
- Remove
Lubrication
top of the gearbox.
The
drive
rod
ends
should
be
top of the gearbox.
lubricated
occasionally
with
a
- Replace the motor. Reassemble.
small
amount
of LGB
Maintenan-
Attention!
ce Oil (50019).
ced,
Cleaning
gears
This model can be cleaned using
(51020).
a mild detergent
and gentle stre-
Attention!
am
of water.
Do
not
immerse
this
drive
model. If this model
is equipped
can cause serious damage to the
with
sound
electronics,
do
not
model.
expose
the
speaker
directly
to
water.
Replacing
the light
bulbs
Front
and
rear
lanterns:
Carefully
pry the lens away from
the
lantern.
Using
tweezers,
remove
and
replace
the
bulb.
Replacing the brushes, pick-up
Reassemble.
shoes
Cab light: Using tweezers, remo-
- Remove
ve and replace the bulb.
joining
Replacing
the smoke
generator
connecting
Pull the safety ring out of the
wheels. Pull the drive rods away
smoke stack (Fig. 3). Use pliers or
from the rear wheels.
tweezers
to pull the old smoke
- Remove
generator out of the stack (Fig. 4).
joining the connecting
Cut the wires to the old generator
the remaining
and attach them to the replace-
the connecting
ment generator (Fig. 5). Insulate
- Remove
the connections
and push the
bottom of the gearbox. Remove
replacement
generator
into
the
the bottom of the gearbox.
stack.
Reassemble.
Make
sure
to
- Remove the power strips.
replace the safety ring.
- Replace the necessary
Reassemble.
Replacing
the traction
tire
- Use a small, straight-blade
scr-
Attention!
ewdriver to gently pry the old
replaced,
traction
tire
out
of
the
wheel
the gears
cant (51020).
groove.
10
warm
the
new traction
in a dish
of warm
water.
scr-
sure
that
the traction
tire
is
the motor
the
hex
head
screws
the
drive
rods
and
rods
at
the
rear
the
rear
wheels.
are
five
screws
on
the
the
front,
remove
the
and
fifth
screws.
the
four
screws
on
the
Remove the
If the motor is repla-
generously
lubricate
the
with LGB
Gear
Lubricant
Make
sure
that
the
rods do not bind.
Binding
and
wheelsets
the
hex
head
screws
the
drive
rods
and
rods
at the rear
the
hex
head
screws
rods to
wheels.
Remove
rods.
all five
screws
on the
parts.
If the
wheelsets
are
generously
lubricate
with LGB Gear Lubri-
Werbung
