Bosch GNH Professional HEAVY DUTY 18V-64 Originalbetriebsanleitung Seite 19

18 | English
Service
Have your power tool serviced by a qualified repair
u
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Tacker safety warnings
Always assume that the tool contains fasteners. Care-
u
less handling of the tacker can result in unexpected firing
of fasteners and personal injury.
Do not point the tool towards yourself or anyone
u
nearby. Unexpected triggering will discharge the fastener
causing an injury.
Do not actuate the tool unless the tool is placed firmly
u
against the workpiece. If the tool is not in contact with
the workpiece, the fastener may be deflected away from
your target.
Disconnect the tool from the power source when the
u
fastener jams in the tool. While removing a jammed
fastener, the tacker may be accidentally activated if it is
plugged in.
Use caution while removing a jammed fastener. The
u
mechanism may be under compression and the fastener
may be forcefully discharged while attempting to free a
jammed condition.
Do not use this tacker for fastening electrical cables. It
u
is not designed for electric cable installation and may
damage the insulation of electric cables thereby causing
electric shock or fire hazards.
Use suitable detectors to determine if there are hid-
u
den supply lines or contact the local utility company
for assistance. Contact with electric cables can cause
fire and electric shock. Damaging gas lines can lead to ex-
plosion. Breaking water pipes causes property damage.
In case of damage and improper use of the battery, va-
u
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
Do not open the battery. There is a risk of short-circuit-
u
ing.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Only use the battery with products from the manufac-
u
turer. This is the only way in which you can protect the
battery against dangerous overload.
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
1 609 92A 81N | (01.08.2022)
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for connecting work in roofing,
encasing and battening, as well as manufacturing wall and
ceiling elements, wood facades, pallets, wood fences, noise-
reduction walls and boxes.
Only the fasteners (nails, staples, etc.) specified in the
"Technical Data" table may be used.
Note: The power tool is not suitable for driving nails into
metal or concrete.
GNH 18V-64 M: Please do not use the power tool in contact
actuation mode with automatic return while working on scaf-
folding, ladders or other platforms and when a change of
working position is required. In this case, only use the single
actuation mode with backup sequence.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Workpiece protector
(2) Discharge lock-off
(3) Clamping lever for opening/closing the shot duct
(4) Thumbwheel for depth stop adjustment
(5) Trigger
(6) Battery release button
(7) Rechargeable battery
(8) Handle (insulated gripping surface)
(9) User interface
(10) Storage for workpiece protector
(11) Belt hook
(12) Magazine
(13) Magazine slider
(14) Nail pusher
(15) Outlet
a)
(16) Nail strip
(17) Magazine spring
(18) On/off switch button (user interface)
(19) On/off switch status (user interface)
(20) Single actuation display (user interface)
(GNH 18V-64 M)
Bosch Power Tools