cecotec IRON PROFESSIONAL Bedienungsanleitung Seite 22

ENGLISH
Temperature knob
Adjust the ironing temperature according to the fabric to be ironed. To enable the Steam
function, select the steam temperature range, otherwise steam will not be sprayed properly.
Temperature indicator light
When the iron is heating up, the temperature indicator will light up. Once the iron has reached
the selected temperature, it will switch off. The temperature indicator light will turn on and off
while the iron maintains the selected temperature during ironing.
Lock button
Place the steam station on the base heat-insulated support and move the lock lever in the
locked position to safely leave the iron on the base. To unlock the iron, move the lock lever to
the unlocked position. You can now start ironing. The whole steam station can be lifted by the
handle, as long as the iron is in the locked position on the base. Fig 4.
Steam trigger
After pressing the power button and choosing the desired steam level, and the indicator lights
stop flashing, the iron will have already reached the temperature at which steam can be used.
Then, lightly press the steam trigger to make steam come out continuously from the soleplate
(fig. 5): When the steam trigger is fully released, the appliance can only be used for dry ironing
without steam. Fig. 5
Steam burst
Press the steam trigger twice in less than one second to activate the steam burst function. Use
the steam burst function to remove stubborn creases.
Filling indicator
When the water level in the tank is low, the Filling indicator will light up, followed by a buzzing
sound; the, the steam generator will stop working. When this happens, add water to the water
tank. To do this, remove the water tank, fill it up through the filling opening, and put it back in
place. Fig. 6
Cleaning indicator
If the Descaling indicator light comes on, the steam generator needs to be cleaned of mineral
residue. To clean it, follow the steps specified in the "Cleaning and maintenance" section. Once
the residue has been removed, the indicator light will switch off.
Cable storage slot
When not in use, the steam supply hose and power cable can be stored in the cable storage
slot.
42 IRON PROFESSIONAL
Auto switch-off
The appliance will automatically switch off after 10 minutes of inactivity.
Dry ironing
- Put the appliance on the heat-insulated bracket.
- Plug the power cord into the outlet. This will cause the temperature indicator light and the
MAX steam indicator light to light up.
- Set the temperature regulator using the temperature knob. Once done, the iron will start
to heat up.
- When the desired temperature is reached, the temperature indicator light will go out. You
can start ironing now.
Warning
Do not touch the soleplate before it cools down!
Steam ironing
- Take the water tank handle to remove it and fill it with water through the filling opening.
Use purified water with little limescale. After that, re-install the water tank. The maximum
water tank capacity is 1.8 L. The water level must not exceed the MAX mark.
- Place the steam station on the base.
- Connect the power cable to the power outlet and press the power button. The default low
steam intensity indicator light will start flashing. There are three modes: low, medium and
high steam intensity. Select the desired steam intensity for each garment according to
your needs. Ensure there is enough water in the tank.
- Adjust the temperature according to the fabric to be ironed, and the indicator light will light
up. The steam station will start emitting heat. Refer to the ironing tips and the table in this
manual when adjusting the temperature.
- The water in the steam generator will heat up and, after a few minutes, the temperature
indicator light will switch off. This indicates that the soleplate has reached the desired
temperature. When the default steam intensity indicator light changes from flashing to
steady, it indicates that the iron is ready for use.
- Lightly press the steam trigger to make steam come out continuously from the soleplate.
Warning
Never direct steam at people!
- After ironing, press the Power button for two seconds: the appliance will switch off along
with all indicators. Unplug the power cable from the wall socket. Be careful: the soleplate
may still be hot. Never touch it if hot. Place the iron on the heat-insulated support until it
has cooled down completely.
ENGLISH
IRON PROFESSIONAL 43