MODEL MOTORS AXI Serie Bedienungsanleitung Seite 2

Fitting procedure for the supplied radial mounting prop adapter.
Direction of Rotation and Motor Timing:
To change the direction of rotation, simply switch over the connection of the outer two cables
between the motor and speed controller, but leave the centre cable connection untouched. The
optimum motor timing is set by the speed controller, however, some high-end programmable
speed controllers allow for some adjustment of the motor timing.
Running-in:
There are no brushes or other moving parts to bed in, so no running-in is required.
Cooling:
Please note that your AXI is a high performance electric motor working under high current
loading which produces some heat. Proper cooling is essential in just that same way as it is with
an internal combustion engine. Overheating of your motor causes increased wear in the
bearings and partial demagnetisation, which decreases performance of the motor. As with all
types of magnetic material, complete demagnetisation of the neodymium magnets can occur at
over 130 C.
Please make sure that cooling air can flow through the holes in the front plate to allow cooling of
the armature and magnets. There is a simple rule of thumb: the area of cooling air intake(s) on
your model should be at least twice the total area of openings on your motor. The area of
cooling outlet(s) should be larger than the intakes to allow for expansion of the heated air.
Care and Maintenance:
Avoid running your motor under dusty or wet conditions. Avoid foreign matter getting in the
cooling holes of your motor. Beware of small bolts, screws and other small items that can be
attracted to the magnets of your motor during installation or maintenance. Do not disassemble
motor. The bearings of this motor are lubricated using special high quality grease that will last
through the whole expected life. Do not use any organic solvents, cleaners or detergents to
clean your motor, these agents may wash out the grease and substantially decrease the lifetime
of your motor. If there is some dirt in your motor (after an accident) do not try to rotate the shaft.
Carefully remove the dirt with compressed air at first. In the case of more serious damage the
motor should be sent for service. Never try to straighten a bent shaft, if the large diameter
hardened steel shaft becomes bent there will be more serious damage inside the motor. If you
are in doubt, please contact the manufacturer to get qualified assistance or repair. Avoid
unnecessary dismantling of your motor.
Safety Notes:
Install only undamaged and balanced propellers and securely tighten with a wrench. Never
touch, or allow any object to come into contact with the rotating propeller. A weakened or loose
propeller may disintegrate or be thrown off which could result in serious injury. Inspect the
propeller after each flight. Discard any propeller that has nicks, scratches or any other visible
defect. Discard the propeller after a crash or contact with ground during a heavy landing even if
the propeller looks undamaged, there could be internal stress or damage resulting in a failure
later. For their safety, keep all onlookers (especially small children) well away (at least 20 feet or
6 metres) when preparing your model for flight. Keep the propeller pointing away from you and
other people, and walk well clear of spectators. First switch on your transmitter, check the
position of the throttle stick (and related switches if any), only then connect your power pack to
the speed controller and switch on the receiver. Always leave space for the propeller to rotate
(in case of a speed controller failure or interference). A stopped propeller could result in damage
to your controller and motor, or even cause fire.
Model Motors Limited Guarantee
This motor and instruction sheet is subject to change without notice. The manufacturer, Model
Motors ltd., guarantees the product to be free from defects in materials or workmanship for a
period of 24 months from the time of its original purchase. Customers must present the original
invoice or sales receipt with the defective product to make a claim under the guarantee. This
guarantee covers none of the following: periodic maintenance and repair or replacement of parts
due to normal wear and tear; any adaptation or changes to upgrade the product from its normal
purpose as described in the instruction manual; transport costs and all risks of transport relating
directly or indirectly to the guarantee of the product; damage resulting from misuse, including
(but not limited to) installation or use of the product in a manner inconsistent with the instruction
manual, repair undertaken by unauthorised service personnel or the customer, accidents,
lightning, water, fire, improper installation, poor cooling or any cause beyond the control of the
manufacturer; defect of the model into which this motor is installed.
Since we, as the manufacturer, have no control over the installation and use of this motor no
representations are expressed or implied as to performance or safety of your completed model.
We wish you many years of trouble free flying with our high performance motors. Fly
safe, have fun!
Sladkovskeho 594
Pardubice 530 03, Czech Republic
e-mail:info@modelmotors.cz,
www.modelmotors.cz
Date of purchase, Stamp