MODEL MOTORS AXI Serie Bedienungsanleitung

High performance electric motors
I I n n s s
Congratulations! Thank you for choosing a product of Model Motors Ltd. Our brushless motors
with neodymium magnets and a rotating case are manufactured using the latest technology
from the highest quality materials. A hardened steel drive shaft mounted in three ball bearings,
and overall robust but lightweight construction ensure long motor life. The unique design of the
motor gives extremely high torque allowing the use of large diameter and high pitch propellers
without the need for a gearbox. To enjoy trouble-free operation of your new motor, please take
time to read through these instructions.
Specification AXI5320/18 AXI5320/28
Voltage range max. 18 cells max. 26 cells
max 6s Li-Poly max 8s Li-Poly
RPM per Volt 370 RPM/V 249 RPM/V
Max. Efficiency 93% 92%
Max. Efficiency 25-55 A (<85%) 10-36 A (<85%)
Current
No load current 1,4A/20V 1,5A
/30V
Max. Loading 78 A/20 s 50 A/60 s
Internal resistance 23m 57m
Dimensions 63x54 mm 63x54 mm
8 mm 8 mm
Shaft Diameter
Weight 495 g 495 g
Recomended 4000-6000g 4000-8000g
model weight
Propeller range. 6s LiPoly 8s LiPoly
18"x10"APC-E 19"x12"APC-E
Direct drive.
6s LiPoly 8s LiPoly
18"x12"APC-E 20"x10"APC-E
The full weight range is applicable for electric gliders.
requiring higher power to weight ratios in the lower half of the weight range. We strongly
recommended the use of folding propellers with this type of motor.
B r u s h l e s s & S e n s
B r u s h l e s s & S e n s
M o t o r A X I
M o t o r A X I
t t r r u u c c t t i i o o n n M M a a n n u u a a l l
AXI5320/34 AXI5330/18 AXI5330/F3A AXI5330/24
max. 32 cells max. 32 cells max. 32 cells
max 10s Li-Poly max 10s Li-Poly max 10s Li-Poly
206 RPM/V 249 RPM/V 235 RPM/V
93% 90% 91%
8-32 A (<85%) 25-60 A (<85%) 23-57 A (<85%]
1,2A 2A 1.8A
45 A/30 s 75 A/30 s 72 A/20s
84m 32m 45m
63x54 mm 63x64 mm 63x64 mm
8 mm 8 mm 8 mm
495 g 652 g 652 g
4000-8000g 5000-10000g 5000-10000g
8s LiPoly 10s LiPoly 10s2p LiPoly
19"x12"APC-E 19"x10"APC-E
PolyQuest 2500XP
AXI20"x13"Carbon
10s LiPoly 10s LiPoly
19"x10"APC-E 20"x8"APC-E
Keep aerobatic and scale models
More information about recommended propellers can find on our website
o r l e s s
o r l e s s
Recommended speed controllers:
S e r i e s JETI ADVANCE 77 plus,8-32cells w/o BEC and max. load 75A
S e r i e s
JETI ADVANCE 90 plus,14-32cells w/o BEC and max. load 90A
Motor Installation
The motor must be mounted on a rigid mounting with four (or eight) M4 bolts screwed into the
front plate. The screws should extend at least 4 mm into the front plate, but not more than 6 mm
(there is a risk of the motor winding damage). The mounting should have holes corresponding to
the holes in the front plate to allow proper cooling of your motor. Please note: the case of the
motor rotates! Beware of unsecured wires, parts or RC flight equipment etc. It is a good idea to
fit a special former separating the motor "from the rest of world".
The AXI motor design with its rotating case significantly increases the need of a robust motor
mount. We strongly recommend the use of a folding propeller even with aerobatic models, even
max. 32 cells
the world F5A champion uses a folding propeller on his motor of a similar design. If you are
max 10s Li-Poly
using your motor at the upper end of it's power range, or if you must use a fixed propeller,
197 RPM/V
please make sure that your motor really is securely mounted.
91%
Radial mounting option
15-38 A (<85%)
A new design of motor with a hardened steel shaft supported in three ball bearings allows your
1,5A
motor to be radial mounted to the front of the motor mounting bulkhead (see pictures). This
feature is very useful for electric conversions of glow power models.
58 A/30 s
Fitting procedure for the supplied front mounting prop adapter.
57m
63x64 mm
8 mm
652 g
5000-10000g
10s LiPoly 20"x10"
10s LiPoly
22"x8"APC-E
www.modelmotors.cz