Milk Frother - Rondell Rde-1113 Die Betriebsanweisung

– In the process of preparing a drink, you can press
the «Double» button (23), the display will show «X2»
(pic. 12) The machine will prepare the next cup of
drink.
Preparation of a drink from ground coffee
To make a drink from ground coffee, in the readiness
mode (pic. 8), press the «Menu/Ground coffee» button
(22) on the control panel.
–
The display will show the manual coffee loading mode
(pic. 15).
–
Open the coffee beans container (8) and remove the
ground coffee funnel lid (28).
–
Pour one portion of ground coffee into the feed
channel using the measuring spoon supplied (pic. 16).
–
Close the ground coffee funnel lid (28) and the lid of
the coffee beans container (8).
–
Use the control panel buttons (7) (Fig. 11) to select
the desired drink.
–
Wait for the end of the drink preparation process.
Note: The volume of the flat measuring spoon from
the delivery set accommodates the optimal amount of
ground coffee for a single drink preparation. To pre-
pare a high-quality drink from ready-ground coffee,
the optimal weight of dry coffee powder is no more
than 9 grams. Be careful not to add more than one
spoonful of ground coffee, as this may damage the
machine. Otherwise, the coffee powder will spill out of
the brewing unit, causing it to clog and damage. It is
unacceptable to pour instant coffee powder or other
freeze-dried coffee-containing mixtures intended for
rapid brewing with hot water into the ground coffee
compartment.

Milk frother

To obtain milk foam, pour milk into a milk container or
insert the milk supply tube (31) into the milk (pic. 24).
–
Place a cup under the coffee supply unit (2). Install
the milk (31) supply tube on the milk system inlet (3)
of the coffee supply unit (2) (Fig. 17) and adjust its
height (Fig. 5).
–
Press the «Frothed milk» button (21).
–
The display will show information about the making
process (Fig. 26).
–
As soon as the temperature of the heating unit reaches
the optimum, frothed milk will start to come out of the
coffee supply unit (2).
–
To stop the milk frothing process, press the «On/
Off» button (16). Or press the «Frothed milk» but-
ton (21) again.
Note: If during the preparation of frothed milk, only milk
comes out of the coffee supply unit (2) or little froth is
formed, then the frother should be adjusted (see the
section «Adjusting the milk supply»).
PREPARATION OF CAPPUCCINO/LATTE
– Place a cup under the coffee supply unit (2).
– Install the milk (31) supply tube on the milk system
inlet (3) of the coffee supply unit (2) (Fig. 24) and
adjust its height (Fig. 5).
– Dip the tube into the milk container (Fig. 17).
– To prepare the type of Cappuccino/Latte drink you
need press one of the buttons: «Cappuccino» (19) or
«Latte» (20).
– The process of preparing the drink will be reflected on
the display (Fig. 18, 19) and will be completed auto-
matically when the coffee machine prepares the vol-
ume of the drink that was programmed.
–
In the process of preparing a drink, you can press
the «Double» button (23), the display will show
«X2» (pic. 12) The machine will prepare the next
cup of drink.
–
To stop the coffee making process, press again the
button of the drink being made: «Cappuccino» (19) or
«Latte» (20) respectively.
Hot water supply
–
Place a cup or other suitable container under the cof-
fee supply unit (2) (Fig. 5). To prevent droplets from
splashing, always adjust the height of the coffee sup-
ply unit (2) to the height of the cup.
–
Press the «Water» button (pic. 20), the water supply
process will start.
– Hot water will be released from the coffee dispensing
unit (2). The display (18) will show the water amount in
milliliters (pic. 20).
– To stop the process, press again the «Water» but-
ton or «On/Off» button (16) on the control panel (7).
31