Unit Operation; Making Drinks - Rondell Rde-1113 Die Betriebsanweisung

– Take out the water tank. To do this, grasp the recess at
the bottom of the tank and pull it up and then towards
yourself (Fig. 2).
– Add clean room temperature water to the water tank.
Do not exceed the MAX mark. It is recommended to fill
the water tank by 3/4 to the MAX mark.
– Install the water tank in the coffee machine and press
its lower left edge until it is completely fixed (Fig. 2).
Notes: The tank (4) can be filled only with clean water at
room temperature. Do not pour hot or ice water, as well
as mineral water and milk into the tank. Failure to comply
with this requirement will lead to cracks in the container or
damage to the device. When installing and removing the
water tank, always hold it by the recess at the bottom of
the tank. It is forbidden to hold the tank by its upper part.
This may cause its damage, fall and spill of the liquid.
– Open the lid of the bean container (8).
– Before the first use, add 30 to 200 g of coffee beans to
the bean container (10) (Fig. 3).
Notes: Put only coffee beans in the container (10). Do not
put there water, ground coffee, sugar, spices, coffee
beans mixed with hard particles. It may cause damage of
the knives and the coffee grinder mechanism.

UNIT OPERATION

Switching the coffee machine on/off
Connect the plug of the power cord (6) of the device to
the mains (Fig. 4).
Press the On button (16) on the control panel (7) (Fig. 6).
When switched on, the coffee machine runs a self-diag-
nosis and automatic washing.
Note:
– To prevent the removable tray (1) from overflowing
with dirty water during rinsing, place a cup or other
suitable container under the coffee supply unit (2)
(Fig. 5).
– To prevent droplets from splashing, always adjust the
height of the coffee supply unit (2) to the height of the
cup (Fig. 2).
– The automatic flushing mode starts when you turn it
on for the first time, as well as when the machine is
activated from standby mode. After the washing pro-
cess is completed, dirty water can be poured out of
the container.
The process of preparing the machine for operation is re-
flected on the display (18) (Fig. 7).
When the preparation process is over, the machine will
switch to the readiness mode. A message will appear on
the display (18) (pic. 8).
To turn off the coffee maker and switch it to shutdown
mode, press and hold the button (16) for 4 seconds. The
rinsing process will start. The information will be shown on
the display (pic. 9). Then the coffee machine will switch to
the «Off» mode (pic. 10).

MAKING DRINKS

– Place a cup under the adjustable coffee spout (2) of the
coffee machine and adjust its height (fig. 5).
– Before the first use, set the grinding degree control
knob (14) of coffee beans to the middle position.
– To make drinks, press one of the control panel but-
tons according to your choice: «Espresso» (26),
«Americano» (25), «Cappuccino» (19), «Latte» (20)
(Fig. 11).
– The preparation process will end automatically when
the coffee machine has made the programmed amount
of drink.
– To get a double portion of the drink, press the «Double»
button (23) before the coffee making process is com-
pleted. The corresponding picture «X2» will appear on
the display (pic. 12).
– To interrupt the process of making the drink at any
stage, press the «On/Off» button (16).
– When the coffee making process is finished, take the
cup with the drink away.
Making americano
– Adjust the coffee dispensing unit height (2) (pic. 5).
– Press the button «Americano» (25) (pic. 13) to make
an americano coffee.
– In the process of preparing a drink, you can press the
«Double» button (23), the display will show «X2» (pic. 12),
and the machine will prepare the next cup of drink.
Making espresso
– Adjust the coffee dispensing unit height (2) (pic. 5).
– Press the «Espresso» button (26) (pic. 14) to make
an espresso.
30