EINHELL GC-HH 18/45 Li T Bedienungsanleitung Seite 21

Use the cutter rail guard (Fig. 2, Item 12)
5.1 Fitting the shoulder strap
(Fig. 3): Attach the carabiner hooks (Item 5a) of
the shoulder strap (Item 5) to the shoulder strap
attachments (Item 6/6a).
5.2 Fitting the tubes
The cordless pole hedge trimmer can be assem-
bled either with or without the extension tube (Fig.
2 / Item 9).
5.2.1 Assembly with extension tube
1. (Fig. 4-5) Make sure that the mounting screws
(Item A) are on the same side and insert the
tube with motor housing/hedge trimmer (Item
10) into the extension tube (Item 9). Screw
the two tubes together with the lock nut (Item
8).
2. (Fig. 6) Insert the extension tube (Item 9) into
the tube with the operating element (Item 11)
and screw the two tubes together with the
lock nut (Item 8). The cordless pole hedge
trimmer has now been screwed together (Fig.
1). To dismantle, proceed in reverse order.
5.2.2 Assembly without extension tube
Insert the tube with the motor housing/hedge
trimmer (Fig. 2 / Item 10) into to tube with the
operating element (Fig. 2 / Item 11) and screw
the two tubes together with the lock nut (Item 8).
The cordless pole hedge trimmer has now been
screwed together. To dismantle, proceed in rever-
se order.
5.3 Using the shoulder strap
Warning! Always use the shoulder strap when
working with the equipment. Switch off the equip-
ment before you take off the shoulder strap (risk
of injury).
1. Slip the shoulder strap (Fig. 7/Item 5) over
your shoulder.
2. Adjust the length of the shoulder strap so that
the strap attachment is at waist level (Fig. 7).
3. The shoulder strap is equipped with a buckle.
Press the hooks together (Fig. 8) if you need
to put down the equipment quickly.
4. To change the strap position on the equip-
ment, slacken the wing nuts (Fig. 3/Item 6b)
by turning them counterclockwise and move
the strap attachment to the desired position
on the tube. Then retighten the wing nuts (Fig.
3/Item 6b) by turning them clockwise.
Anl_GC-HH_18-45_Li_T_SPK13.indb 20 Anl_GC-HH_18-45_Li_T_SPK13.indb 20
GB
5.4 Adjusting the angle of the motor housing/
hedge trimmer (Fig. 9)
Press the lock-off button (Item 10a) and adjust
the angle of the hedge trimmer head (Item 10) to
any of 7 latching positions.
5.5 Turning the handle (Fig. 10)
Press the two lock-off buttons (Item 4) and turn
the handle (Item 1) 90° to the left or 90° to the
right.
5.6 Fitting the battery (Fig. 11)
Press the pushlock button (T) of the rechargeable
battery and
push the battery into the battery mount provided.
When the battery pack is positioned as in Fig.
11, make sure that the pushlock button latches
in place! To remove the battery pack, proceed in
reverse order.
5.7 Charging the battery (Fig. 11-12)
1. Take the battery pack out of the equipment.
Do this by pressing the pushlock button (T).
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
into the mains socket outlet. The green LED
will then begin to fl ash.
3. Insert the battery pack into the battery char-
ger.
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts.
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
- 20 -
08.03.2022 11:16:28 08.03.2022 11:16:28