Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Connect the machine only to a socket with the
properly installed earthing contact.
The table drill is equipped with a no-volt trip that is
designed to protect the operator from an undesi-
red restart following a drop in voltage. Should this
occur, the machine must be manually restarted.
Check the drill and its safety devices for damage
and impairments. Do not use the drill if you disco-
ver any damage or impairments.
5.4 Setting the height of the motor unit
(Fig. 2 and 9)
Important! Adjust the height only after the motor
has been switched o !
The height of the motor unit (7) can be adjusted to
suit the size of the workpiece and the length of the
plug-in tool.
·
Make sure that the hand wheel (8) is in its
starting position.
·
First undo the clamping screw (10) on the
back of the motor unit (7).
·
Then use the crank (11) to set the required
height.
·
Finally retighten the clamping screw (10).
To limit the depth, undo the fastening screw (9)
on the motor unit (7). Set the required maximum
depth and retighten the fastening screw (9).
6. Operation
6.1 Switching on/switching o
·
To switch on, first actuate the green ON but-
ton "I" (5). The display will light up and "OFF"
will appear.
·
To start the tool, press the LED button (15).
The tool will start at minimum speed.
·
To switch off, press the LED button again.
Take care not to overload the tool. If the sound
of the motor drops in pitch during operation, it is
being overloaded.
Do not overload the tool to the point where the
motor comes to a standstill.
Always stand in front of the machine during ope-
ration.
6.2 Inserting the tool (Fig. 10)
Make sure that the power plug is removed from
the socket-outlet before changing tools. Only cy-
lindrical tools with the stipulated maximum shaft
diameter may be clamped in the scroll chuck (3).
Only use a tool that is sharp and free of defects.
GB
Do not use tools whose shaft is damaged or
which are deformed or awed in any other way.
Use only accessories and attachments that are
speci ed in the operating instructions or have
been approved by the manufacturer. If the pillar
drill should become jammed, switch o the machi-
ne and return the drill to its starting position.
6.3 Handling the keyless chuck
Your pillar drill is equipped with a keyless chuck.
This enables tools to be changed without the
need for an additional chuck key. To do so, insert
the tool in the quick-change drill chuck and tighten
by hand.
6.4 Setting the rotational speed
Mechanical gear selector
Important! Actuate the gear selector switch
(4) only after the machine has been switched
o !
You can use the gear selector switch to preselect
2 speed ranges:
Gear 1:
Low speed range 220 – 880 min-1, recommended
for work involving large drill diameters.
Speed 2:
High speed range 650 – 2550 min-1, recommen-
ded for work involving small drill diameters.
Note:
(Fig. 4)
If the gear selector switch (4) fails to engage cor-
rectly, turn the drill chuck (3) a little by hand until it
latches in place.
Electronic speed adjustment
·
After you have switched off the machine, the
word "OFF" will appear in the display (6).
·
Press the "+" button or the "-" button to increa-
se or decrease the speed.
6.5 Setting the zero point
·
To set the zero point, lower the motor unit (7)
at minimum speed until the drill bit rests on
the workpiece.
·
Now use the speed button (12) to switch
from "Speed – rpm" to "Depth – mm" and then
press the zero point button (13). The display
will change to "0.0mm".
·
Use the hand wheel (8) to return the motor
unit to its starting position.
·
Now use the speed button (12) to switch from
"Depth – mm" back to "Speed – rpm" and
- 13 -
Werbung
