Bosch Intuvia 100 Originalbetriebsanleitung Seite 13

puter must be in the holder for this. Undo the fastening
screw (11) of the clamp with a hex key until the holder (7)
can be moved. Turn the holder (7) until the bottom side of
the on-board computer is accessible. Insert the locking
screw (6) and bolt it with the on-board computer. Align the
holder (7) correctly with the on-board computer and tighten
the fastening screw (11) again with a hex key.
Please note: The locking screw is not designed to prevent
theft.
Operation
Connecting the On-board Computer with the
eBike (Pairing)
Your on-board computer is generally already connected with
the eBike. If this is not the case, proceed as follows:
– Install the eBike Flow app.
– Activate Bluetooth® on your smartphone and open the
eBike Flow app.
– Briefly press the Bluetooth® button.
– The device identification is shown on the on-board com-
puter.
– Select the required tool with the same identification in
the eBike Flow app.
You can find further information at the following link:
www.bosch-ebike.com/en/help-center/intuvia-100.
Depending on the smartphone's operating sys-
tem, the eBike Flow app can be downloaded
free of charge from the Apple App Store and
the Google Play store.
Use your smartphone to scan the code in order
to download the eBike Flow app.
Switching the on-board computer on/off
Switch on the eBike.
To switch on the on-board computer, it must first be placed
in the holder. The on-board computer contact (4) is pressed
automatically.
Switch on the operating unit and gently move the eBike.
The following options are available for switching off the on-
board computer:
– Press the ON/OFF button on the operating unit to switch
off the eBike.
The on-board computer is also switched off.
– Remove the on-board computer from its holder.
The on-board computer switches off automatically after
60 s.
Power supply for the on-board computer
The on-board computer is provided with energy by the
CR2450 coin cell.
Changing the coin cell (see figure C)
When the coin cell of the on-board computer is nearly
drained, you're shown a corresponding message on the on-
board computer. Open the battery compartment cover (2)
Bosch eBike Systems
with a slotted screwdriver (12), remove the used coin cell
and insert a new one (type CR2450). You can obtain the
Bosch-recommended coin cells from your bicycle dealer.
When inserting the coin cell, ensure that the coin cell is in-
serted with the lettering facing upwards and that the rubber
seal (14) is correctly positioned.
Seal the battery compartment and slide the on-board com-
puter onto the holder.
Battery charge indicator of the eBike battery
The on-board computer shows the state of charge of the
eBike rechargeable battery in per cent. A notification is dis-
played once when the state of charge falls below 30 %, and
again when it falls below 10 %. The notification can be con-
firmed, or otherwise the display switches off automatically
after 5 s.
Operation
The Bluetooth® button (1) has various functions. If the on-
board computer was connected with an operating unit and
has been removed from the holder, the displays can be
switched within 60 s. To do so, briefly press the
Bluetooth® button (1). The on-board computer is then set to
stand-by mode.
Note: If you are not going to be using your eBike for several
weeks, remove the on-board computer from its holder and
set the on-board computer to storage mode. To do so, press
the Bluetooth® button (1) for 8–11 s.
If you put the on-board computer back into the holder and
move the eBike, the storage mode will deactivate automatic-
ally.
The reset button (5) serves to reset the on-board computer
to factory settings and delete all connections.
The on-board computer can be operated using one of the op-
erating units shown. The functions of the buttons on the op-
erating units can be found in the following overview.
Depending on how long it is pressed for, the select button
has 2 functions.
3-button operating unit
English – 3
0 275 007 3BI | (03.02.2023)