Werbung
Verfügbare Sprachen
Verfügbare Sprachen
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles
and grasping surfaces do not allow for safe
handling and control of the tool in unexpected
situations.
5) Battery tool use and care
a) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one
type of battery pack may create a risk of fire when
used with another battery pack.
b) Use power tools only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another. Shorting the battery terminals
together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
e) Do not use a battery pack or tool that is
damaged or modified. Damaged or modified
batteries may exhibit unpredictable behaviour
resulting in fire, explosion or risk of injury.
f) Do not expose a battery pack or tool to fire
or excessive temperature. Exposure to fire or
temperature above 130 °C may cause explosion.
g) Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specified in the instructions.
Charging improperly or at temperatures outside
the specified range may damage the battery and
increase the risk of fire.
6) Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
b) Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
SAFETY INSTRUCTIONS
FOR PEDESTRIAN-
CONTROLLED SNOW
THROWERS
General
This machine is capable of amputating hands and feet
and throwing objects. Failure to observe the following
safety instructions could result in serious injury.
Training
1)
Read, understand and follow all instructions
on the machine and in the manual before
operating this unit. Be thoroughly familiar with
the controls and the proper use of the machine.
Know how to stop the unit and disengage the
controls quickly.
2)
Never allow children to operate the machine.
Never allow adults to operate the equipment
without proper instruction.
3)
Keep the area of operation clear of all persons,
particularly small children.
4)
Exercise caution to avoid slipping or falling,
especially when operating the machine in
reverse.
Preparation
1)
Thoroughly inspect the area where the machine
is to be used and remove all doormats, sleds,
boards, wires and other foreign objects.
2)
Disengage all clutches and shift into neutral
before starting the motor.
3)
Do not operate the machine without wearing
adequate winter garments. Avoid loose fitting
clothing that can get caught in moving parts.
Wear footwear that will improve footing on
slippery surfaces.
4)
Always wear safety glasses or eye shields
during operation or while performing an
adjustment or repair to protect eyes from
foreign objects that may be thrown from the
machine.
5)
Adjust the collector housing height to clear
gravel or crushed rock surface.
6)
Never attempt to make any adjustments while
the motor is running (except when specifically
recommended by manufacturer).
Operation
1)
Do not put hands or feet near or under rotating
parts. Keep clear of the discharge opening at
all times.
2)
Exercise extreme caution when operating on or
crossing gravel drives or walks. Stay alert for
hidden hazards or operating near public roads.
3)
After striking a foreign object, stop the
motor, remove the wire from the spark plug,
disconnect the cord on electric motors,
thoroughly inspect the snow thrower for
any damage, and repair the damage before
restarting and operating the snow thrower.
4)
If the machine should start to vibrate
abnormally, stop the motor and check
immediately for the cause. Vibration is generally
a warning of trouble.
5)
Stop the motor whenever you leave the
operating position, before unclogging the
EN
7
Werbung
