SLV RIFFA Betriebsanleitung Seite 3

ENGLISH
OPERATING MANUAL FOR
PENDANT FITTING
RIFFA PD-101 / PD-102
Read this short manual carefully and keep it accessible for further
reference!
SAFETY MESSAGES
Disregard of the safety messages may lead to danger of life, burning or
fire!
• Installation, mounting or works on the electrical connection may only be
carried out by an approved electrician.
• The product may not be modified or converted.
• Do not hang or fasten anything on the product, especially no decoration.
• Do not cover the product - provide free air circulation.
• In case of a malfunction you may NOT touch the product or operate it
further. Disconnect the product from the power supply by an external
switch or by the fuse.
A malfunction exists when:
• visible damages appear.
• the product does not work properly (e.g. flickering).
• smoke, steam or crackling sounds appear.
• smell of burning is recognisable.
• an overheating is recognisable (e.g. by discolouration of adjacent
surfaces).
Operate the product only after maintenance and examination by an
approved electrician!
• This product is not intended to be used by children. Ensure that children do
not suffer any harm e.g. by burns from hot surfaces or by electrical shock.
Additional safety messages are indicated by this symbol:
USE AS DIRECTED
This product serves exclusively lighting purposes and may:
• only be used with a voltage of 230V ~50Hz.
• only be installed according to safety class I (one).
• only be operated when firmly mounted on a stable, even and tilt-fixed
surface.
• only be operated on normally or not flammable surfaces.
• only be used in dry condition,
• not in damp or dirt-endangered rooms.
• not in areas of high air humidity.
• not be exposed to strong mechanical loads or to strong contamination.
OPERATION
To achieve a homogeneous light appearance the tubes must be operated 100
hours continuously on first operation. After that, the dimmer may be used to
adjust the light intensity.
MAINTANANCE AND CARE
Light source
Exchange the light source always before it reaches its lifespan, to avoid
personal injuries, or damages of the luminaire or other objects.
Disconnect the product from the power supply, before you exchange the
light source. Let the light source cool down before replacement.
Use only light sources that are suitable for the product. Suitable light
sources are indicated on the type label.
• Suitable light sources: T16(T5), G5, 54W
• Replacing the light source
• Remove the cover.
• Remove the used light source.
• Insert the new fluorescent tube into the recesses of the sockets. With a
quarter-turn the tube is fixed.
• Attach the cover.
Care
Disconnect the product from the power supply and let it cool down, before
you clean the product.
• Clean the product on a regular basis using a slightly moistened, soft and fluff-
free cloth. Please also note additional supplied notes on maintanance and
care.
STORAGE AND DISPOSAL
Storage
• The product must be stored in a dry and clean environment. Do not strain
the product mechanically during storage.
After a damp or soiling storage the product may only be installed after
checking its condition by an approved electrician.
.
Disposal (European Union)
• Do not dispose the product with the regular household waste! Products
marked with this sign must be disposed according to the directive(WEEE,
2003/108) on electrical and electronic devices at local collection points for
such devices!
INSTALLATION
(only by an approved electrician)
Switch off the mains or respectively the connection lead before doing any
works!
Use only parts, which are supplied with the product or are described as
accessories!
Inspect the product for loose parts inside the housing. When there are loose
parts inside the housing and these are not explicitly described the product may
not be installed or operated.
Use the supplied fastening material only when it is suited for the installation
background. If this is not the case use only fastening material suiting the
installation background.
Unpacking
• Carefully take the product out of the packaging removing any transport
safeguards.
• Before disposal of the packaging material make sure that all components
of the product are removed.
Installation place
• The product is solely suited for installation on a ceiling.
Installation steps (read completely before installation)
• Install the luminaire as shown in the figure A.
• Adjusting the pendulum length: Adjust the pendulum lamps utilising the
wire fixer. You may adapt the length of the lead also. Loosen the strain
relief on the canopy. Disconnect the wires from the terminal block and
shorten the lead to the desired length. Reconnect the wires with the
terminal block as before. Refasten the strain relief. Do not strain the lead!
• Dimming: Use only a suitable dimmer with a control voltage of 1-10V (e.g.
art.-no. 470505). Connect the dimmer with the (+) and (-) clamps of the
connection clamp.
• Electrical Connection
• The product must be able to be separated by an all pole separation
from the current supply.
• For electric connection attach the black or brown wire (live conductor)
of the connection lead with the clamp L and the blue wire (neutral
conductor) of the connection lead with the clamp N. The green-yellow
wire (protective conductor) of the connection lead has to be tightly
screwed into the earth clamp of the product.
• Inserting the light source
• Insert the fluorescent tube into the recesses of the sockets. With a
quarter-turn the tube is fixed.
Connecting two lamps
• Mechanical connection
• Install the luminaires as shown in the figure B1.
• Electrical connection
• Only RIFFA PD-101, art.-no. 158304, may be connected with each other
electrically.
• Install the luminaires as shown in the figure B2.
• Remove the connection lead from the second luminaire.
Check if the product functions properly and is securely fixed!
art.-no. 158304/14 © 25.03.2013 SLV Elektronik GmbH,
Daimlerstr. 21-23, 52531 Übach-Palenberg, Germany,
Tel. +49 (0)2451 4833-0
Technical Details are subject to change.