one minute. By default, your monitor will activate the out of range sound
alert, emitting two double beeps every 3 seconds to warn you that the
two units are not communicating. The alarm will stop sounding after one
minute, or when you press any button, or when you bring the monitor close
to the camera and the connection is re-established.
If you want to cancel the sound alert , follow these steps:
1. Press the menu button (5) on the monitor to access the main menu.
2. Press the left (9) or right (7) navigation button until the wheel settings
icon is highlighted.
3. Press the down (8) navigation button until the alerts icon is highlighted.
4. Press the OK/ zoom button (10) and then press the OK/ zoom button
(10) again to activate or cancel the out of range sound alert.
If the alarm is red the sound alert is off, if it is green the sound alert is on.
Note: To get a better quality communication signal between the
monitor and the camera, use the monitor aerial (15) by simply pulling
it out. When the baby monitor is not in use we recommend you store
the aerial to prevent it from getting caught or breaking.
5.2.9. STANDBY MODE
With standby mode you can press the on / off button (1) directly to switch
off the screen and save power while you continue to listen to sounds.
To reactivate the image, simply press the on/ off button (1) once again.
5.2.10. MAIN MENU
Press the menu (5) on your monitor to access the main menu.
5.2.10.1. CAMERA MENU
5.2.10.1.1. ADD CAMERA AND PAIRING
The pairing between the monitor and the camera will be done under two
circumstances:
- If you want to add an additional camera.
- If the monitor and the camera are not paired.
The monitor and the original camera leave the factory with channel
1 programmed, nonetheless, if for some reason, they are not,
you can link them manually following the steps indicated below.
To pair the camera and the monitor follow the next steps:
1. Press the menu button (5) to display the menu and show the highlighted
camera icon.
2. Press the down (8) navigation button until the add / remove icon is
displayed and press the OK / zoom button (10) to go into the sub-menu.
3. Press the up (6) or down (8) navigation button to select the camera
you want to add.
4. Press the OK / zoom button (10) to search for a camera unit.
5. Press the pairing button on the camera (VIII) for 5 seconds.
6. Once paired the image of the camera will show immediately on the
monitor unit screen.
For various reasons you may lose the connection between the monitor and
a camera which is already connected. Should this be the case, repeat the
process explained above to connect the camera with the monitor again.
Note 1: Before starting the pairing procedure, make sure the camera
and the monitor are close to one another and that the camera is
correctly plugged in and is switched on.
Note 2: Each camera can be linked just with one monitor at a time.
Nota 3: If the monitor and the camera, for some reason, have left the
factory without being paired, you will have to do it manually adding
the camera to channel 2. You won't be able to pair the camera again
with channel 1 until you have paired it in another channel and remove
the channel 1 camera.
5.2.10.1.2. DELETE CAMERA
To delete one of the cameras connected, follow the next steps:
1. Press the menu button (5) to display the menu and show the highlighted
camera icon.
2. Press the up (6) or down (8) navigation button until the add / remove
icon is displayed and then press the OK / zoom button (10) to go into
the sub-menu.
3. Press the up (6) or down (8) navigation button to select the camera
you want to remove and then press the OK / zoom button (10) again.
Note: A channel needs to be deleted before pairing to a new camera unit.
5.2.10.1.3. CHOOSING THE CAMERA
The device is designed to allow different areas to be monitored with up
to two cameras.
To select the camera you want to view, follow the steps described below:
1. Press the menu button (5) to display the menu and show the highlighted
camera icon.
2. Press the OK / zoom button (10) to go into the sub-menu.
3. Press the up (6) or down (8) navigation button to select the camera
you want to see (camera 1, camera 2).
4. Press the OK / zoom button (10) to go to the selected camera.
Note 1: The additional camera reference compatible with this baby
monitor is 89506 digital camera 3.5" easy.
Note 2: In the upper corner of the screen (B) you can see which camera
you are viewing.
5.2.10.1.4. SCAN MODE
This function automatically cycles through your paired camera channels
to display each camera for 12 seconds. This function can be used only
when you have more than 1 camera unit paired. To enter in this mode:
1. Press the menu button (5) to display the menu and show the highlighted
camera icon.
2. Press the OK / zoom button (10) to go into the sub-menu.
3. Press the up (6) or down (8) navigation button until the scan mode
icon is highlighted.
4. Press the OK zoom button (10).
5. The scan mode icon (C) will be displayed at the top of the screen to
indicate that it is activated.
Note 1: If one of the cameras is out of range, has no battery or is not
switched on, the monitor will warn you and the main screen will be
displayed during that period of time.
Note 2: To cancel scan mode, follow the same steps described above
and select from the options available: see camera 1, see camera 2.
5.2.10.2. VOX MODE
This mode allows you to control sound activation of your baby
monitor. If you activate VOX mode on the monitor and there is no
sound around the camera for 30 seconds, it will stop transmitting. The
monitor screen will turn itself off when the camera is not transmitting.
When the camera detects any sound louder than the set sensitivity
level, it will start transmitting the signal to the monitor again.
To cancel this function and see the monitored area continuously,
disconnect VOX mode on the monitor.
· VOX mode OFF: The camera transmits continuously, enabling you
to monitor your baby or the area you wish to protect continuously.
· VOX mode ON: The camera only transmits when it detects a sufficiently
loud sound, depending on the level selected, around the camera.
To activate VOX mode, follow the steps described below:
1. Press the menu button (5) to display the menu.
2. Press the right (7) or left (9) navigation button until the VOX icon
is highlighted.
3. Press the OK / zoom button (10) and the right (7) or left (9) navigation
button to select sensitivity level 1/2/3.
4. Set sensitivity level "1" if your baby tends to sleep soundly and cries
softly; level "3" if your baby tends to make sounds while sleeping or makes
quite loud sounds before starting to cry and level "2" if you think your
baby's behaviour doesn't fit in with either of the previous patterns.
5. Press the down navigation button (8) and then the OK / zoom button
(10) to activate the VOX function. The VOX function is on when it shows
green and off when it shows red.
6. The VOX icon (F) will be displayed on the top part of the LCD screen.
You may exit the function in the following manner:
1. Press the Menu button (5).
2. Do not touch the monitor for 15 seconds.
To activate VOX mode quickly, you can press the VOX mode on / off button
on the monitor (11). This will activate VOX mode with the last settings,
that is, at the level of sensitivity set the last time it was used. To change
the sensitivity level, follow the steps described above.
5.2.10.3. TEMPERATURE ALERT
From this menu you can turn the temperature sound alert on and off, and
set it to suit your needs. Follow these steps:
1. Press the menu button (5) to display the menu.
2. Press the right (7) or left (9) navigation button until the alerts icon
is highlighted.
3. Press the down (8) navigation button until the temperature alert icon
is highlighted.
13
ENGLISH