Herunterladen Inhalt Inhalt Diese Seite drucken

miniland digimonitor 3.5" easy Bedienungsanleitung Seite 12

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 28
ENGLISH
C. Scan mode
D. Night vision
E. Monitor volume
F. Vox Mode
G. Temperature
H. Battery level / monitor charge indicator
I. Talk to the baby activated indicator
J. Zoom
4.2. CAMERA FUNCTIONS AND CONTROLS (FIGURE 2)
I. On / off button
II. Photo sensor
III. Camera lens
IV. Infra-red vision LEDs
V. Microphone
VI. Speaker
VII. Temperature sensor
VIII. Pairing button
IX. Charging LED
X. USB-C power connector
5. INSTRUCTIONS FOR USE
5.1. BEFORE USE
5.1.1. PARENTAL UNIT POWER SUPPLY AND BATTERY USE
The monitor, or parent unit, is designed to be used with the battery or
with the AC/DC adapter supplied. Your baby monitor is supplied with a
rechargeable 3.7V 1200mAh Li-ion battery for the monitor.
By default, when the battery level has dropped too low, the volume LEDs
(3) and the low battery icon (H) will flash and the monitor will start to
emit a beep every five seconds.
To charge the monitor:
1. Connect the power supply adaptor to the USB-C socket (14). For safety
reasons, use only the adaptor supplied.
2. Connect the adaptor to the mains. The battery will be fully charged in
less than five hours.
While charging:
3. The charging LED (2) on the monitor will light up in red, and if the
unit is switched on the battery icon (H) on the screen will indicate that
the battery is charging.
4. When the battery is fully charged, the charging LED (2) will turn off.
5.1.2. BABY UNIT POWER SUPPLY
The camera, or baby unit, of this baby monitor is designed to be used
with the AC / CC adaptor supplied.
To charge the camera:
1. Connect the adaptor cable to the USB-C socket on the camera (X).
Use only the adaptor supplied.
2. Connect the adaptor to the mains.
WARNING: Choking hazard – Keep the cord out of the baby's reach.
NEVER place a camera with cables less than 1 meter from the cot.
Never use extension cords with AC adapters. Use only the AC adapters
supplied.
5.2. OPERATION
5.2.1. TURNING THE UNITS ON/OFF
5.2.1.1. MONITOR
To switch the monitor on, press the on/off button (1) for at least 4 seconds.
When the monitor has been switched on, the welcome screen will be
displayed.
To switch the monitor off, press the on/ off button (1) for at least 4 seconds.
If for some reason your monitor blocks, press and hold the power button
(1) until the unit turns off.
5.2.1.2. CAMERA
To turn the camera on or off, keep the power button (I) pressed in for
two seconds.
The on / off LED (IX) will come on for two seconds when the unit is
switched on and flash twice when the unit is switched off.
When you have installed the camera and turned it on, you can see
the images and listen to the sounds captured in your baby's room
via the monitor.
5.2.2. MONITOR VOLUME
Press the OK / zoom button (10) and the up (6) or down (8) navigation
button to show the volume bar. Then, press the up (6) or down (8)
navigation button to select the desired volume, from 0 (mute) to 6 (very
loud). The default volume setting is 3.
To exit this function, you can do the following:
1. Press the menu button (5) or the OK / zoom button (10).
2. Do not touch the monitor for 15 seconds.
Note: The volume icon (E) will appear at the top of the screen along
with a number indicating the volume level.
5.2.3. MONITOR BRIGHTNESS
Press the OK / zoom button (10) to show the brightness bar. Then,
press the left (9) or right (7) navigation button to select the desired
brightness, from 1 through to 7. The default brightness setting is 4.
To exit this function, you can do the following:
1. Press the menu button (5) or the OK / zoom button (10).
2. Do not touch the monitor for 15 seconds.
5.2.4. SETTING THE CAMERA ANGLE
The camera on the 3.5" baby monitor can be angled manually. To do this,
turn the camera to the left or to the right, and / or move the lens up or
down until you get the position you want. The camera has 355º vision,
but it does not rotate on its own axis, so do not force it. When you turn
the camera sideways and it reaches its limit at around 180º, do not try to
make it turn further. The camera has a 53º vertical angle of view, so do
not force it when it reaches its limit.
Note: For a clearer view, clean the camera lens with a slightly damp
cloth.
5.2.5. TALKING TO THE BABY
You can talk to your baby from the parents' unit (for example, to calm them
down and so they understand you're on your way) or to your partner (if
he or she is in the baby's room).
Press the button to talk to the baby (12), keep it pressed down and speak
into the front of the monitor. While this function is in use, a microphone
icon (I) will be visible at the bottom of the LCD screen. Release the button
when you have finished speaking to listen to sounds coming from the
baby's room.
Bear in mind you won't be able to hear your baby while you're talking to
them. To listen again, release the button (12).
5.2.6. DIGITAL ZOOM
If you wish, you can increase the size of the image viewed by using the
zoom function.
Keep the OK / zoom button (10) pressed for two seconds to access this
function.
When in this mode, you can continue to move the image with the monitor
navigation buttons (up (6), down (8), right (7) or left (9)).
A zoom icon (J) will be displayed at the bottom of the LCD screen.
You can move through the zoom image with the right (7), left (9), up
(6) and down (8) navigation buttons.
To exit the zoom function, keep the OK / zoom button (10) pressed for
at least 2 seconds.
5.2.7. INFRARED NIGHT VISION (AUTOMATIC)
The infrared night vision function allows the camera to pick up images in
dark or low light conditions. In this mode, only black and white images
will be displayed on the monitor and only objects located less than 2
meters away can be seen.
The camera automatically changes to infrared mode when there is
insufficient light for normal vision.
When the camera is in this mode, the night vision icon (D) will be
displayed on screen.
Note: The light sensor (II) is located at the top of the camera. Take
care not to cover the sensor with any object to prevent the camera
from entering night mode when there is light in the room.
5.2.8. OUT OF RANGE WARNING
If the monitor is further away than allowed from the camera (check the
technical specifications), the image will be lost and the welcome screen
will be displayed on your monitor. The out of range symbol (A) and the
4 green volume LEDs (3) will flash in the top left corner of your screen for
12

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

89505

Inhaltsverzeichnis